MIMAKI UJF-3042 MkII

To Next Page

To Previous Page

UJF-3042MkIISeries/UJF-6042MkIISeries Operation Manual

May, 2022

MIMAKI ENGINEERING CO.,LTD.

2182-3 Shigeno-otsu, Tomi-shi, Nagano 389-0512 JAPAN

D203043-42-1005022

Main Page

Table of Contents2
Caution6
Cdrh Regulation6
Disclaimer of Warranty6
FCC Statement (USA)6
Interference to Televisions and Radios6
Requests6
Foreword7
On this Operation Manual7
Restriction in Use7
For Safe Operation8
Symbols8
Safety Interlock13
Position of the Warning Label14
Before Use17
Installing the Machine18
Moving this Machine18
Where to Install the Machine18
Configuration and Function19
Front19
Carriage20
Emergency Switch20
Rear20
Indicator Light Unit21
Operation Panel22
About Table25
About Tap Position25
Connecting the Cables27
Connecting the USB2.0 Interface Cable27
Instructions for Using the Table27
About Ink Bottle28
Connecting the LAN Cable28
Connecting the Power Cable28
Kinds of Ink that Can be Used28
Caution in Handling of Ink Bottles29
Setting Ink Bottles30
About Media34
Precautions in Handling the Media34
The Sizes of Media that Can be Used34
Menu Mode35
Basic Operations37
Operation Flow38
Turning the Power off39
Turning the Power ON/OFF39
Setting the Media40
Set the Media in Another Method42
Test Printing43
About Head Cleaning44
Head Cleaning44
Perform Head Cleaning Depending on the Test Printing Result44
Perform Test Printing with the Test Pattern for Checking White Ink44
Interruption of Printing45
Printing an Image from Source Data45
Starting the Printing Operation45
Checking Printing Data that Is Being Received or Has Been Received46
If You Open the Cover During Printing46
When [! WORK High] Is Displayed46
Setup47
About Head Height MENU48
Head Height MENU Table48
Gap Check49
Setting the HEAD GAP49
Setting the Media Thickness49
About ORIGIN SETUP MENU51
ORIGIN SETUP MENU Table51
Setting the X Offset (LOC)52
Setting the X Offset (REM)52
Setting the y Offset (LOC)52
Setting the y Offset (REM)52
Setting the Z Origin53
About SETUP MENU54
SETUP MENU Table55
Setting of LOGICAL SEEK56
Setting of Media Correction56
Setting of INK LAYERS57
Setting of REFRESH LEVEL57
Setting of UV Adjval57
Setting of UV MODE57
Setting of WORK CHANGE57
Setting of AUTO CLEANING58
Setting of FAN MODE58
Setting of MAPS459
Setting of PRINT FLUSHING LEVEL59
Setting of the Misregistration Adjust60
Setting of LT Mode61
Setting of Scan Speed61
Setting of SUCTION WIPER61
About MACHINE SETUP MENU62
MACHINE SETUP MENU Table63
Setting a AUTO Power-Off64
Setting a KEY BUZZER64
Setting Time64
Setting Unit (Length)64
Setting Event Mail Function65
Setting the Network65
Setting a Ionizer (Option)70
Setting a LANGUAGE70
Setting of Remote Control70
Initializing the Settings71
Recognize Connection Options71
Setting the Time of the Head Temperature to Standby71
About NOZZLE CHECK MENU72
INFORMATION MENU Table72
Printing Check Flow73
Printing Operations at "Nozzle Missing" Judg- Ment and Error Occurrence73
Printing Operations at "Nozzle Missing" Judgment and Error Occurrence73
Setting the Judgment Condition74
Setting the NOZZLE RECOVERY74
Setting the Printing Check74
About INFORMATION MENU75
INFORMATION MENU Table75
Displaying the Information76
Maintenance77
Cleaning Exterior Surfaces78
Cleaning the Table78
Precautions in Cleaning78
Routine Maintenance78
When this Machine Is Left Unused for a Long Time78
About MAINTENANCE MENU80
MAINTENANCE Menus At-A-Glance81
Cleaning the Wiper and Cap82
Maintaining the Capping Station82
Cleaning the Mist Filter84
Nozzle Wash85
Nozzle Wash (When PR-200 Ink Using)86
Washing the Ink Discharge Passage88
When the Machine Is Not Used for a Long Time88
Sub Tank Maintenance89
Cleaning the Ink Head and the Area Around It90
Cleaning the Ink Head and the Area Around It490
White Maintenance90
Clean the Bottom of the LED Lamp and the Bot- Tom of the Mist Filter91
Nozzle Recovery Function92
Checking the UV Lamp Usage93
Reset the Set Value93
Solving the Ink Overflow Problem93
Automatic Maintenance Function94
Setting the Cleaning Intervals and Type94
Setting the Refreshing Intervals94
(When Using Rubber Wiper) Replace the Wiper/ Wiper Absorber95
(When Using Rubber Wiper) Replace the Wiper/Wiper Absorber95
(When Using Suction Wiper)Replace the Nozzle95
(When Using Suction Wiper)Replace the Nozzle Cap95
Replacing Consumables95
Replacing the Mist Filter97
Replacing the Mist Filter Box97
If a Waste Ink Tank Confirmation Message Ap- Pears98
If a Waste Ink Tank Confirmation Message Appears98
LED Glass Replacement98
Ink Tank Confirmation Message Is Displayed4-2199
Replacing the Waste Ink Tank before the Waste99
Replacing the Waste Ink Tank before the Waste Ink Tank Confirmation Message Is Displayed99
If Check Wiper Waste Inktank Warning Appears100
Replacing the Waste Ink Tank before the "Check101
Replacing the Waste Ink Tank before the "Check Wiper Waste Inktank" Warning Is Displayed101
Supplying Antifreeze Liquid101
Wiper Waste Inktank" Warning Is Displayed101
Troubleshooting105
Image Quality Is Poor106
Power Does Not Turn on106
The Machine Does Not Start Printing106
Troubleshooting106
Ink Bottle Warning Appears107
Nozzle Is Clogged107
When the Ink Leakage Occurs107
Warning / Error Messages108
Warning Messages108
Error Messages111
Appendix117
- Specifications118
- Machine Specifications118
- Ink Specifications119
- Setting Orders of Ink Bottles120
- Sheet for Inquiry121
- LICENSE Library123

MIMAKI UJF-3042 MkII - Page 125

Table of Contents

Other manuals for MIMAKI UJF-3042 MkII

Related product manuals