I
I
FrameMaker
Ver55(PC)
EPlO!WEP1085/EP2030 DWREASSEMBLY, ADJUSTMENT
98.04.13
(7)
Replacement of the Ozone Filter
.....................................................
D-39
2-8. FUSING
UNIT
..........................................................................................
D-40
(1)
Removal of the Fusing Unit .............................................................
D-40
(2)
Cleaning of the Pre-Fusing Guide Plate
..........................................
D-41
(3)
Removal of the Upper Fusing Roller
...............................................
D-41
(4)
Cleaning of the Upper Fusing Roller
...............................................
D-43
(5)
Cleaning of the Upper Paper Separator Fingers .............................
D-43
(6)
Cleaning of the Fusing Thermistor
..................................................
D-43
(7)
Removal of the Lower Fusing Roller
...............................................
D-43
(8)
Cleaning of the Lower Fusing Roller
...............................................
D-44
(9)
Cleaning of the Lower Paper Separator Fingers .............................
D-44
(10)
Disassembly of the Exit/Duplex Switching Unit (Option)
................. D-45
3. ADJUSTMENT
.................................................................................................
D-49
3-1. JIGS AND TOOLS USED
........................................................................
D-49
3-2. ADJUSTMENT REQUIREMENTS LIST
..................................................
D-50
3-3. ADJUSTMENT OF SWITCHES
...............................................................
D-51
(1)
Adjustment of Front Door Interlock Switch
S21
...............................
D-51
3-4. ELECTRICAL/IMAGE ADJUSTMENTS
..................................................
D-52
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Adjustment of the Maximum Exposure Lamp Voltage for
the Manual Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-52
Adjustment of the Optimum Exposure Setting in the Manual Mode D-55
Adjustment of the Optimum Exposure Setting in the Auto Mode
. . . . D-56
Adjustment of the ATDC Sensor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-57
Adjustment of the Aperture Blades
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-58
Adjustment of the Multi Bypass Table Reference Position
. . . . . . . . . . . . . . D-59
Adjustment of the 1
st/2nd
(23 cpm copier only)
Drawer Reference Position
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-60
Adjustment of the Paper Lifting Plate Springs (2nd Drawer):
23 cpm
copier only
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-61
Adjustment of the
Leading
Edge
Registration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-62
(10)
Adjustment of the Image Leading Edge Erase Width ......................
D-66
(11)
Adjustment of the Image Erase Lamp Position
...............................
D-68
3-5. OTHER
ADJUSTMENTS
.........................................................................
D-69
(1)
Adjustment of the Scanner/Mirrors Carriage Position .....................
D-69
(2)
Adjustment of the Gap Between the Doctor Blade and
Sleeve Roller
...................................................................................
D-70
(3)
Adjustment of the Original Size Detecting Board
............................
D-71
4.
MISCELLANEOUS
..........................................................................................
D-72
4-l. INSTALLATION OF THE PLUG-IN COUNTER MOUNTING BRACKET
(OPTION)
.....................................................................................
..-
.........
DJ2
I
I
I
I
ii
To Next Page
Loading...
