Mircom FX-2003-12DS - User Manual

For the latest compatability information visit www.mircom.com/deviceguide
FX-2000
Intelligent Analog Fire Alarm Control Panel
LT-657 Rev 15
December 2016
Installation and Operation Manual

Summary

Mechanical and Chassis Installation

Chassis Installation

Provides instructions for installing the main chassis into enclosures.

Mounting the Chassis into the BBX-1072 ADS or BBX-1072 ARDS Enclosure

Details mounting the chassis into specific BBX enclosures.

Mounting the Chassis into the BB-5008 or BB-5014

Details mounting the chassis into BB-5008/BB-5014 enclosures.

Mounting the Chassis into the UB-1024 DS and DOX-1024 DS;R Enclosure

Details mounting the chassis into UB-1024DS/DOX-1024DS/R enclosures.

Display and Adder Modules Mounting Locations

FX-2003-6 DS;FX-2003-12 DS;FX-2003-6 DS-16 LED Compact Main Chassis

Shows mounting locations for display and adder modules in compact chassis.

FX-2017(S)-12 DS Mid-size Main Chassis

Shows mounting locations for display and adder modules in mid-size chassis.

FX-2009(S)-12 DS Large Main Chassis

Shows mounting locations for display and adder modules in large chassis.

ECX-0012 Expander Chassis for FX-2009-12 DS

Shows mounting locations for display and adder modules in expander chassis.

Mounting the Boards to the BBX-1024 XT Chassis

Details mounting boards within the BBX-1024XT chassis.

Module Settings

Main Fire Alarm Modules (MD-764 Part of Main Chassis)

Details settings and jumpers for the main fire alarm module.

Main Fire Alarm Super Module (MD-757 Part of “S” Version Main Chassis)

Details settings and jumpers for the main fire alarm super module.

DM-1008 A Hardwire Detection Adder Module

Details jumpers and connections for the DM-1008A detection module.

SGM-1004 A Hardwire NAC Signal Adder Module

Details operation and jumpers for the SGM-1004A NAC signal adder module.

RM-1008 A Hardwire Relay Adder Module

Details connections and jumpers for the RM-1008A relay adder module.

Polarity Reversal and City Tie Module (Model PR-300)

Details hardware configuration and jumpers for the PR-300 module.

UDACT-300 A Main Board

Details jumpers, LEDs, and cable connections for the UDACT-300A.

ALC-198 S Single Intelligent Analog Loop Controller Module

Describes power, RS-485, DIP switches, and jumpers for the ALC-198S module.

ALC-396 S Dual Intelligent Analog Loop Controller Module

Describes power, RS-485, DIP switches, and jumpers for the ALC-396S module.

ALC-H16 Hardwire Loop Controller Module

Details power, RS-485, jumpers, and connectors for the ALC-H16 module.

Field Wiring

Main Fire Alarm Module Terminal Connections

Details terminal connections for the main fire alarm module.

Analog Loop Wiring

Explains analog loop wiring configurations (Class B, Style 7, Style 6).

Loop Terminal Connections - Class B

Shows Class B analog loop terminal connections and legend.

Loop Terminal Connections - Style 7

Shows Style 7 analog loop terminal connections and legend.

Loop Terminal Connections - Style 6 (Formerly Class A)

Shows Style 6 analog loop terminal connections and legend.

Single Loop Terminal Connections - Class B

Shows Class B single loop terminal connections and legend.

Single Loop Terminal Connections - Style 7

Single Loop Terminal Connections - Style 6

Detection Module (DM-1008 A) Terminal Connections

NAC Signal Module (SGM-1004 A) Terminal Connections

Relay Module (RM-1008(A)) Terminal Connections

Polarity Reversal and City Tie Module (PR-300) Wiring

UDACT-300 A Main Board Terminal Connections

Power Supply Connections

System Checkout

Before Turning the Power On

Lists pre-power-on checks for system installation.

Power-Up Procedure

Outlines the steps for powering up the fire alarm control panel.

Troubleshooting

Provides a table of common system messages and their descriptions.

Indicators and Controls

Figure 45 DSPL-420 Main Display Indicators and Controls

Figure 46 DSPL-420-16 TZDS Main Display Indicators and Controls

Operation

Single Stage Operation

Describes how the system operates in a single-stage alarm mode.

Two Stage Operation

Describes how the system operates in a two-stage alarm mode.

Pre-Signal Operation

Appendix A: Specifications

FX-2003-6 DS and FX-2003-6 DS-16 LED Specifications

FX-2003-12 DS, FX-2003-12 XTDS, FX-2009-12 DS, FX-2009 S-12 DS Specifications

FX-2017-12 ADS and FX-2017 S-12 ADS Specifications

FX-2000 System Modules and Annunciator Specifications

Appendix B: Compatible Devices

FX-2000 Series Compatible Addressable Loop Devices (UL)

Lists UL-compatible addressable loop devices for the FX-2000 series.

FX-2000 Series Compatible Two-Wire Smoke Detectors (UL)

Lists UL-compatible two-wire smoke detectors for the FX-2000 series.

FX-2000 Series Compatible Four-Wire Smoke Detectors (UL Listed)

Lists UL-compatible four-wire smoke detectors for the FX-2000 series.

FX-2000 Series Compatible Signalling Devices (UL Listed)

Lists UL-compatible signalling devices for the FX-2000 series.

FX-2000 Series Compatible Addressable Loop Devices (ULC)

Lists ULC-compatible addressable loop devices for the FX-2000 series.

FX-2000 Series Compatible Hardwire Smoke Detectors (ULC)

Lists ULC-compatible hardwire smoke detectors for the FX-2000 series.

FX-2000 Series Compatible Synchronized Modules and Strobes

Appendix C: Power Supply and Battery Calculations

Power Requirements (All currents are in amperes)

Battery Capacity Requirement:

Appendix D: Remote Annunciator Panels

RA-1000 & RAM-200 Series

RA-1000 & RAM-200 Models

RAX-LCD

Models

Appendix E: DIP Switch Settings Summary

RA-1000

DIP switch settings for the RA-1000 series.

MGD-32

DIP switch settings for the MGD-32 module.

RAX-LCD

DIP switch settings for the RAX-LCD.

RAM-208 or RAM-216

DIP switch settings for RAM-208/216.

Appendix F: Alarm Verification Timing

ALC-396 S

Appendix G: Wiring For Supervised Output Module

Figure 48 UL 864 Wiring for Addressable Supervised Output Module

Mircom FX-2003-12DS Specifications