Mirion Technologies MBD-2

Questions and Answers

B
Bradley CarrilloSep 18, 2025
What can cause saturation in Mirion Technologies MBD-2 Measuring Instruments detectors?
- N
  nicholas64Sep 18, 2025
  Saturation in one or more detectors of your Mirion Technologies Measuring Instruments can be caused by: * Overflow Total Dose: the total dose reaching/exceeding 3,750 cGy * Overflow Gamma: the gamma dose reaching/exceeding 2,500 cGy * Overflow Neutron: the neutron dose reaching/exceeding 1,250 cGy
P
Peggy MorganAug 25, 2025
What does it mean if my Mirion Technologies Measuring Instruments display 'dbAt'?
- Z
  ztaylorAug 25, 2025
  If 'dbAt' is cycling on the display of your Mirion Technologies Measuring Instruments, it means less than 25% battery life remains. If 'dbAt' is permanently displayed, the battery is exhausted. In both cases, replace the batteries with 3 new CR1025 batteries.
J
Jose ReevesAug 25, 2025
What to do if the Mirion Technologies MBD-2 device restarts after a battery change?
- P
  pcooperAug 26, 2025
  If your Mirion Technologies Measuring Instruments device restarts after a battery change, it indicates that internal data memory was found to be corrupt, and the device performed a self-hard reset to clean the memory. If this error message occurs under normal use (without high dose or neutron exposure), remove the device from service.
K
kevin89Aug 27, 2025
What to do if Mirion Technologies MBD-2 Measuring Instruments show parameter error?
- J
  John ValenzuelaAug 27, 2025
  If your Mirion Technologies Measuring Instruments device shows a Parameter Error, remove the device from service and return it for Warranty Repair.
R
ricky45Sep 22, 2025
What to do if Mirion Technologies Measuring Instruments detectors can't report a measurement value?
- L
  Laura Smith MDSep 22, 2025
  If one or more detectors on your Mirion Technologies Measuring Instruments device cannot report a measurement value, remove the device from service. Remove and replace the battery and observe the display. If the problem persists, return the device for Warranty Repair.
M
Marc TuckerSep 23, 2025
What to do if Mirion Technologies MBD-2 Measuring Instruments report recombination?
- G
  garrisonkatherineSep 23, 2025
  If recombination has occurred in an ionization chamber element due to a gamma flash or neutron burst event on your Mirion Technologies Measuring Instruments device, it requires a reset of the device. Remove the device from service.
Y
Yolanda GomezSep 9, 2025
What to do if Mirion Technologies Measuring Instruments cannot determine reading result position?
- H
  Heidi PowellSep 10, 2025
  If your Mirion Technologies Measuring Instruments device cannot determine the reading result position in flash memory due to a failure in flash memory access or corruption of memory contents, restart the device by removing and re-inserting the battery. If the error message repeats, remove the device from service.
S
Shannon ReynoldsSep 12, 2025
What to do if Mirion Technologies MBD-2 Measuring Instruments reading fails due to corruption of result memory?
- B
  buckleyvictoriaSep 12, 2025
  If the measurement result reading fails on your Mirion Technologies Measuring Instruments device due to corruption of the result memory, restart the device by removing and re-inserting the battery. If the error message repeats, remove the device from service.
T
Tony RojasSep 3, 2025
What to do if Mirion Technologies MBD-2 Measuring Instruments show low battery voltage?
- N
  nancymarshallSep 3, 2025
  If your Mirion Technologies Measuring Instruments device shows a low main battery voltage (less than 2200 mV) with no battery icon and a permanent 'PbAt' message, replace the main battery with model CR2450.
V
Vanessa MooreSep 1, 2025
What to do if Mirion Technologies MBD-2 report exceeding maximum dose?
- M
  michaelpettySep 1, 2025
  If your Mirion Technologies Measuring Instruments device reports that one or more detector elements has exceeded the maximum dose, it requires a reset of the device. Remove the device from service.