Mitsubishi FR-A740-00023-EC - Page 88

78
Parameter List
Parameter List
Energy saving monitor
891
Cumulative power monitor digit shifted
times
0 to 4, 9999 1 9999 267
892 Load factor 30 to 150% 0.1% 100% 267
893
Energy saving monitor reference
(motor capacity)
0.1 to 55/0 to 3600kW *2
0.01/
0.1kW
*2
Inverter
rated
capacity
267
894
Control selection during commercial
power-supply operation
0, 1, 2, 3
1 0 267
895 Power saving rate reference value 0, 1, 9999 1 9999 267
896
Power unit cost 0 to 500, 9999
0.01 9999 267
897
Power saving monitor average time 0, 1 to 1000h, 9999
1 9999 267
898
Power saving cumulative monitor clear 0, 1, 10, 9999
1 9999 267
899 Operation time rate (estimated value) 0 to 100%, 9999 0.1% 9999 267
Calibration parameters
C0
(900)
CA terminal calibration
⎯ ⎯ ⎯
251
C1
(901)
AM terminal calibration
⎯ ⎯ ⎯ 251
C2
(902)
Terminal 2 frequency setting bias
frequency
0 to 400Hz
0.01Hz 0Hz 282
C3
(902)
Terminal 2 frequency setting bias 0 to 300% 0.1% 0% 282
125
(903)
Terminal 2 frequency setting gain
frequency
0 to 400Hz
0.01Hz 50Hz 282
C4
(903)
Terminal 2 frequency setting gain 0 to 300%
0.1% 100% 282
C5
(904)
Terminal 4 frequency setting bias
frequency
0 to 400Hz 0.01Hz 0Hz 282
C6
(904)
Terminal 4 frequency setting bias 0 to 300%
0.1% 20% 282
126
(905)
Terminal 4 frequency setting gain
frequency
0 to 400Hz
0.01Hz 50Hz 282
C7
(905)
Terminal 4 frequency setting gain 0 to 300% 0.1% 100% 282
Analog output
current calibration
C8
(930)
Current output bias signal
0 to 100% 0.1% 0% 251
C9
(930)
Current output bias current
0 to 100% 0.1% 0%
251
C10
(931)
Current output gain signal
0 to 100% 0.1% 100%
251
C11
(931)
Current output gain current
0 to 100% 0.1% 100% 251
Calibration parameters
C12
(917)
Terminal 1 bias frequency (speed) 0 to 400Hz
0.01Hz 0Hz 282
C13
(917)
Terminal 1 bias (speed) 0 to 300% 0.1% 0% 282
C14
(918)
Terminal 1 gain frequency (speed) 0 to 400Hz 0.01Hz 50Hz 282
C15
(918)
Terminal 1 gain (speed) 0 to 300%
0.1% 100% 282
C16
(919)
Terminal 1 bias command (torque/
magnetic flux)
0 to 400%
0.1% 0% 288
C17
(919)
Terminal 1 bias (torque/magnetic flux) 0 to 300%
0.1% 0% 288
C18
(920)
Terminal 1 gain command (torque/
magnetic flux)
0 to 400%
0.1% 150% 288
C19
(920)
Terminal 1 gain (torque/magnetic flux) 0 to 300% 0.1% 100% 288
C38
(932)
Terminal 4 bias command (torque/
magnetic flux)
0 to 400% 0.1% 0% 288
C39
(932)
Terminal 4 bias (torque/magnetic flux) 0 to 300%
0.1% 20% 288
C40
(933)
Terminal 4 gain command (torque/
magnetic flux)
0 to 400%
0.1% 150% 288
C41
(933)
Terminal 4 gain (torque/magnetic flux) 0 to 300%
0.1% 100% 288
⎯
989
Parameter copy alarm release 10, 100
1 10/100 *2 386
PU
990
PU buzzer control 0, 1
1 1 383
991 PU contrast adjustment 0 to 63 1 58 383
Func-
tion
Parameter Name Setting Range
Minimum
Setting
Increments
Initial Value
Refer
to
Page
Customer
Setting