Mitsubishi WD3300U User Manual (English)

Other manuals for Mitsubishi WD3300U

User Manual52 pages

Brochure & Specs2 pages

Questions and Answers:

T
Timothy KingAug 17, 2025
Why does my Mitsubishi WD3300U Projector display 'NO SIGNAL'?
- K
  Kimberly FreemanAug 17, 2025
  The 'NO SIGNAL' message on your Mitsubishi Projector may appear because the connected device is not powered on or has a problem. Ensure the external device is outputting signals, especially if it's a notebook computer. Also, verify the cable connecting the device is not defective and is connected to the correct terminals on the projector. Make sure the connected device is correctly selected as the input source. If using an extension cord, replace it with the supplied cable to check if that resolves the issue; if it does, use an RGB signal amplifier with the extension cord.
B
brittanybrownAug 20, 2025
What to do if no image appears on Mitsubishi WD3300U Projector screen?
- B
  Bryan JacksonAug 20, 2025
  If no image appears on your Mitsubishi Projector screen, first, ensure that AV mute is off by pressing the AV MUTE button and that the lens cap is removed. Note that the lamp may take up to 1 minute to light up. If the lamp doesn't light, wait a few minutes and try again. If the projector was turned off before the lamp cooled down, wait for the fan to stop, then press the POWER button. Also, set SCART INPUT in the QUICK MENU or FEATURE menu to OFF. Check that the intake vent is clean and the cables connected to external devices are not broken. If using an extension cable, replace it with the supplied cable; if this works, add an RGB signal amplifier to the extension cable.
A
Amanda WigginsAug 23, 2025
Why is my Mitsubishi WD3300U remote control not working?
- C
  Charlene CrawfordAug 23, 2025
  If the remote control for your Mitsubishi Projector isn't working, check that the batteries are correctly loaded and not weak. Ensure the remote control sensor isn't exposed to direct sunlight or fluorescent light. Use the remote control within its specified operation range and at least 10 cm away from the projector.
P
Patricia McgeeAug 26, 2025
Why is my Mitsubishi WD3300U overheating and showing 'TEMPERATURE!!'?
- J
  jacksonalexandraAug 26, 2025
  The 'TEMPERATURE!!' message on your Mitsubishi Projector indicates that the ambient temperature is too high, which can cause the lamp to go out. Eliminate any causes of the rise in ambient temperature. This message also appears if the air inlet or outlet grille is blocked, which will also cause the lamp to go out. Remove any objects blocking the air inlet or outlet grille.
A
Angel HendrixAug 28, 2025
How to fix shaking images on Mitsubishi WD3300U Projector?
- N
  nancy89Aug 28, 2025
  To fix shaking or displaced images on your Mitsubishi Projector, first, check that the cable connected to the external device isn’t intermittent and ensure the cable’s plug is firmly connected. Project an image with many characters, like a help menu, and press the AUTO POSITION button. If issues persist, some computers output out-of-spec signals; adjust the SIGNAL menu accordingly.
C
Craig ChavezAug 31, 2025
How to fix a blurred image on Mitsubishi WD3300U Projector?
- M
  Michael WangAug 31, 2025
  To correct blurred images on your Mitsubishi Projector, adjust the focus. Clean the lens. Try pressing the ? or ? button on the remote control to eliminate flicker. Adjust TRACKING and FINE SYNC in the SIGNAL menu. Also, adjust BRIGHTNESS and CONTRAST in the QUICK MENU or IMAGE menu. Ensure the projector and screen are perpendicular to each other.
J
John BrewerSep 3, 2025
Why are my Mitsubishi WD3300U images too dark?
- D
  David FaulknerSep 3, 2025
  If the projected images from your Mitsubishi Projector are too dark, adjust BRIGHTNESS and CONTRAST in the QUICK MENU or IMAGE menu. If the issue persists, consider replacing the lamp.
K
Kelly BakerSep 5, 2025
How to resolve distorted images on Mitsubishi WD3300U Projector?
- A
  Andrew GraySep 5, 2025
  To resolve distorted images on your Mitsubishi Projector, adjust the projector and the screen so that they are perpendicular to each other.
E
Emily GlennSep 8, 2025
How do I fix the Mitsubishi WD3300U Projector when the menu can't be used?
- D
  Daniel CarrSep 8, 2025
  If the menu on your Mitsubishi Projector can't be used, the microcomputers inside the projector may be operating incorrectly due to noise. Turn off the main power, wait about 10 minutes, and then turn it back on.
K
Kelly MillerSep 12, 2025
Why is there no audio output from my Mitsubishi WD3300U?
- D
  Douglas HawkinsSep 12, 2025
  If there is no audio output from your Mitsubishi Projector, check that the volume isn’t set too low. When the external device is connected with an HDMI cable, set the audio output of the device to PCM output.

Mitsubishi WD3300U Specifications

General

Projection distance	- m
Vertical scan range	50 - 95 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	DLP
Contrast ratio (typical)	2300:1
Screen size compatibility	300 \
Projector native resolution	WXGA (1280x800)
Video in	Yes
Resolution	1280 x 1024 pixels
Aspect ratio	4:3, 16:9
RS-232 ports	1
Compatibility	PC Mac
Power supply type	AC
Dimensions (WxDxH)	450 x 373 x 188 mm
Power requirements	100 - 240 V, 50 - 60 Hz
Connectivity technology	Wired
Focus	Auto
Focal length range	- mm
Service life of light source	4000 h
Noise level	26 dB
Dot clock scanning frequency	162 MHz
Analog signal format system	NTSC, PAL, SECAM
RMS rated power	10 W
Headphone outputs	2
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Wi-Fi	No
Power consumption (standby)	- W
Power consumption (typical)	430 W