Mitsubishi WD385U-EST

Questions and Answers

M
Megan WilsonNov 21, 2025
What to do if my Mitsubishi WD385U-EST Projector power can not be turned on?
- L
  Linda AlvarezNov 21, 2025
  If your Mitsubishi Projector won't turn on, begin by checking the indicators to see if they are on or off and how they are lighting. Ensure the power cord is correctly connected to both the projector and the wall outlet. If there are any obstructions blocking the air inlet or outlet grille, remove them, unplug the power cord, let the projector cool off, plug the cord back in, and then press the POWER button. Also, make sure that you are not exposing the air outlet grilles to hot air emitted from a heating appliance. After the STATUS indicator stops blinking, press the POWER button. Note that if you unplug the power cord while the fan is rotating, the lamp may not turn on for about 1 minute when you plug the power cord next time, and the lamp can’t turn on again for 1 minute after it goes o...
A
amataAug 25, 2025
How to fix a Mitsubishi WD385U-EST displaying 'No signal'?
- A
  amolinaAug 26, 2025
  If your Mitsubishi Projector displays a 'No signal' message, first ensure that the connected device is powered on and functioning correctly. Check if the external device is outputting signals, especially if it's a notebook computer. Verify that the cable connecting the projector to the external device is not defective and is connected to the correct terminals. Also, confirm that the connected device is correctly selected as the input source. If using an extension cord, try replacing it with the supplied cable to see if that resolves the issue; if it does, consider using an RGB signal amplifier with the extension cord.
C
cody57Aug 27, 2025
What to do if my Mitsubishi Projector shows no image on the screen after turning it on?
- G
  Gregory StantonAug 27, 2025
  If your Mitsubishi Projector shows no image after turning it on, try these steps: First, cancel AV mute by pressing the AV MUTE button. Check that the lens cap is removed. Note that it can take about 1 minute for the lamp to light up. If the projector was turned off before the lamp cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. Press the POWER button to turn back on the POWER indicator. Ensure the intake vent is clean and the lamp cover is closed. Check the cables connected to external devices for damage. If using an extension cable, replace it with the supplied cable to check for improvement; if images display correctly, consider adding an RGB signal amplifier to the extension cable.
R
richard55Aug 27, 2025
Why does my Mitsubishi Projector ask for a password?
- M
  Michael BrownAug 27, 2025
  If your Mitsubishi Projector is displaying a password screen, it means the password lock feature has been enabled in the Password menu. To proceed, you will need to enter the correct password. If you do not know the password, contact the person responsible for managing the projector.
B
Bailey BartlettAug 29, 2025
Why are my Mitsubishi WD385U-EST images shaking or displaced?
- C
  Christopher BoydAug 29, 2025
  If the images projected by your Mitsubishi Projector are shaking or displaced, first check that the cable connecting the projector to the external device isn’t intermittent. Ensure the cable's plug is firmly connected to the external device's connector. Then, press the AUTO POSITION button. Note that some computers may output out-of-spec signals; in this case, adjust the Signal menu. If the input signal is a WXGA video signal, confirm the setting selected in WXGA in the Option menu; otherwise, select Off.
D
Derek RomeroSep 16, 2025
Why is there no audio output from my Mitsubishi WD385U-EST?
- L
  Lindsay HollandSep 16, 2025
  If there is no audio output from your Mitsubishi Projector, first check that the volume isn’t set too low. Then, check the Audio Input setting. When the external device is connected with an HDMI cable, set the audio output of the device to PCM output.
J
jameswilliamsSep 14, 2025
Why are my Mitsubishi WD385U-EST images flickering?
- R
  Robin AdamsSep 14, 2025
  If the images projected by your Mitsubishi Projector are flickering, it may be because after the POWER button or ON button on the remote has been pressed, or the Lamp Mode setting has changed, images may be flickering until the lamp lights stably. This is an expected behavior. When selecting the input signal, Auto Position, and Image, the projected image may be flickering temporarily. This is not a product malfunction.
M
Michael ThompsonSep 15, 2025
Why are my Mitsubishi WD385U-EST images twitching?
- C
  Carlos MillerSep 15, 2025
  If the images from your Mitsubishi Projector are twitching, it may be vibrating. Set Auto Keystone to Off or lower the VOLUME ? button of the Remote control.
J
Jessica BrownSep 6, 2025
Why are my Mitsubishi Projector images wavy?
- C
  Cheryl PrattSep 6, 2025
  If the images projected by your Mitsubishi Projector appear wavy, ensure that the plugs of the cables are securely connected to the external devices. Also, keep the projector away from equipment that generates interfering radio waves. Note that when the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal; in this case, readjust the keystone so that the amount of keystone correction is as small as possible.
R
Randy KimSep 4, 2025
Why are there white or black dots on my Mitsubishi WD385U-EST images?
- R
  Regina GonzalesSep 4, 2025
  The presence of white or black dots on projected images from your Mitsubishi Projector is normal for a DLP™ projector and does not indicate a malfunction. A very small number of pixels may be persistently visible or invisible, but this is not a sign of system failure. Over 99.99% of the pixels are effective.