Mitsubishi WD385U-EST

Questions and Answers

T
Timothy GordonSep 10, 2025
Why is there a different color tint on my Mitsubishi WD385U-EST Projector?
- C
  Crystal HamiltonSep 12, 2025
  When comparing images projected by two projectors, tints in the displayed images may be different because of variation between their optical components. This is not a malfunction. When comparing the image projected by this projector with those displayed on the television or PC monitor, tints in the displayed images may be different because of difference in the range of color reproducibility. This is not a malfunction.
R
Rachel ElliottSep 9, 2025
Why is the tint incorrect in my Mitsubishi WD385U-EST images?
- G
  Gloria BlackSep 9, 2025
  If the tint in the images projected by your Mitsubishi Projector is incorrect, check that Computer Input in the Signal menu is correctly set. Also, verify that the cable connected to the external device isn’t broken.
A
Angela DuncanAug 25, 2025
What to do if my Mitsubishi Projector power turns off by itself?
- D
  Daniel HaynesAug 25, 2025
  If your Mitsubishi Projector turns off unexpectedly, it might be due to blocked intake or exhaust vents. Remove any obstructions and then wait for the fans to stop (until the STATUS indicator goes out). Unplug the power cord, wait about 10 minutes, plug it back in, and press the POWER button. If the STATUS indicator is steady red, the lamp likely needs replacement. Also, ensure that the Auto Power Off setting is disabled. A deteriorated lamp may also cause the projector to turn off after a short time.
J
Jessica BrownSep 6, 2025
Why are my Mitsubishi Projector images wavy?
- C
  Cheryl PrattSep 6, 2025
  If the images projected by your Mitsubishi Projector appear wavy, ensure that the plugs of the cables are securely connected to the external devices. Also, keep the projector away from equipment that generates interfering radio waves. Note that when the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal; in this case, readjust the keystone so that the amount of keystone correction is as small as possible.
M
Mariah MendezSep 5, 2025
Why are fine streaks seen on my Mitsubishi WD385U-EST Projector images?
- S
  Sandy DixonSep 5, 2025
  Fine streaks on projected images from your Mitsubishi Projector are often due to interference with the screen surface and do not indicate a malfunction. Consider replacing the screen or slightly displacing the focus. Vertical or horizontal streak noise may also appear depending on the DVD player, game console, or computer you are using. Enabling the LPF may reduce this noise.
R
Randy KimSep 4, 2025
Why are there white or black dots on my Mitsubishi WD385U-EST images?
- R
  Regina GonzalesSep 4, 2025
  The presence of white or black dots on projected images from your Mitsubishi Projector is normal for a DLP™ projector and does not indicate a malfunction. A very small number of pixels may be persistently visible or invisible, but this is not a sign of system failure. Over 99.99% of the pixels are effective.
J
John HaleSep 3, 2025
Why do afterimages persist on my Mitsubishi WD385U-EST screen?
- G
  gstantonSep 3, 2025
  If you notice afterimages persisting on the screen of your Mitsubishi Projector, projecting an evenly bright image for a while can help improve this phenomenon. This 'image burn-in' can occur if a stationary image is displayed for a long time.
I
Isaiah RyanSep 1, 2025
How to fix blurred images on my Mitsubishi WD385U-EST Projector?
- M
  michael89Sep 1, 2025
  If the images projected by your Mitsubishi Projector are blurred, start by adjusting the focus. Clean the lens. You can also press the ? or ? button on the remote control to eliminate flicker. Further adjustments can be made by adjusting Tracking and Fine sync in the Signal menu, and Brightness and Contrast in the Picture menu. Lastly, ensure the projector and screen are perpendicular to each other.
A
Amanda HarrisAug 31, 2025
Why are my Mitsubishi WD385U-EST images dark?
- K
  kelly07Aug 31, 2025
  If the images projected by your Mitsubishi Projector appear dark, try adjusting the Brightness and Contrast settings in the Picture menu. If adjusting these settings does not resolve the issue, the lamp may need to be replaced.
R
Ralph CochranAug 30, 2025
How to fix distorted images on my Mitsubishi Projector?
- M
  Marissa CruzAug 30, 2025
  If the images projected by your Mitsubishi Projector are distorted, adjust the position of the projector and the screen to ensure they are perpendicular to each other.