Mitsubishi WD570U - User Manual

Questions and Answers

K
kevingriffinAug 19, 2025
What to do if my Mitsubishi WD570U shows no signal?
- M
  matthew33Aug 19, 2025
  If your Mitsubishi Projector displays no signal, first turn on the power of the connected device or check if there is something wrong with it, especially if it's a notebook computer. Verify that the external device outputs signals and that the cable connected to it isn't defective. Ensure the projector is connected to the external device using the correct terminals and that the connected device is correctly selected as the input source. If using an extension cord, replace it with the supplied cable to check if images are projected correctly; if so, use an RGB signal amplifier with the extension cord.
T
Taylor HartAug 21, 2025
Why do white or black dots appear on my Mitsubishi WD570U images?
- K
  Kendra KirbyAug 22, 2025
  The appearance of white or black dots on projected images from your Mitsubishi Projector is normal for a DLP projector and does not indicate a malfunction. A very small number of pixels may be visibly or invisibly persistent, but they are not a sign of system malfunctions.
J
Justin PowersAug 25, 2025
How to fix distorted images on my Mitsubishi WD570U Projector?
- K
  Kayla ConnerAug 25, 2025
  To correct distorted images on your Mitsubishi Projector, adjust the projector and the screen so that they are perpendicular to each other.
J
James ParkerAug 26, 2025
Why do afterimages persist on the screen of my Mitsubishi Projector?
- H
  Holly BarronAug 26, 2025
  To improve afterimages persisting on the screen of your Mitsubishi Projector, keep projecting an evenly bright image. This phenomenon, known as 'image burn-in,' may occur if a stationary image is displayed for a long time.
R
Robert CortezAug 28, 2025
Why is there a different color tint on my Mitsubishi Projector?
- J
  Jennifer FoleyAug 28, 2025
  When comparing images projected by two projectors, different tints may appear due to variations between their optical components; this is not a malfunction. Similarly, when comparing the image projected by this projector with those on a television or PC monitor, tints may differ because of differences in the range of color reproducibility; this is also not a malfunction.
A
Alejandro DavisAug 30, 2025
Why are my Mitsubishi WD570U Projector images flickering?
- A
  adrianaestradaAug 30, 2025
  If the images from your Mitsubishi Projector are flickering, note that after pressing the POWER or ON button on the remote or changing the Lamp Mode setting, images may flicker until the lamp lights stably, which is normal. Also, when selecting the input signal, Auto Position, and Image, the projected image may flicker temporarily; this is not a product malfunction.
A
Amber JonesSep 1, 2025
Why is my Mitsubishi WD570U twitching?
- K
  Kenneth HendersonSep 1, 2025
  If your Mitsubishi Projector images are twitching, the projector may be vibrating. Set Auto Keystone to Off or lower the VOLUME button of the Remote control.
D
David FordSep 3, 2025
Is it normal for warm air to come from the exhaust vents of my Mitsubishi Projector?
- K
  Karina BartlettSep 3, 2025
  Yes, it is normal for warm air to come from the exhaust vents of your Mitsubishi Projector. This air comes out after cooling the inside of the projector; although it may feel hot, it is not a malfunction.
K
kimtinaSep 5, 2025
Why can’t I use the menu on my Mitsubishi WD570U Projector?
- M
  mauricebrownSep 5, 2025
  If you can’t use the menu on your Mitsubishi Projector, the microcomputers inside the projector may be operating incorrectly due to noise. Press the POWER button to turn off the lamp, unplug the power cord from the wall outlet, wait about 10 minutes, plug the power cord back in, and try again.
I
imoonSep 7, 2025
What does the “Temperature!!” message mean on my Mitsubishi WD570U?
- J
  Jennifer BarreraSep 8, 2025
  The “Temperature!!” indication on your Mitsubishi Projector appears when the ambient temperature rises high, which can cause the lamp to go out. This indication also appears when the air inlet or outlet grille is blocked, which can also cause the lamp to go out. Remove any objects blocking the air inlet or outlet grille.

Summary

Important Safeguards

Place of Installation

Specifies environmental conditions for projector placement to ensure safety and performance.

Overview

Remote Control Overview

Describes the components and functions of the projector's remote control.

Remote Control Operation

Battery Installation and Replacement

Instructions for inserting and replacing batteries in the remote control.

Installation Guide

Projection Layouts

Provides projection distance and image size data for specific projector models.

Aspect Ratio Considerations

Details installation based on screen aspect ratios (4:3, 16:10, 16:9).

Mounting Methods

Explains ceiling and rear projection installation methods.

Basic Connections

AV Device Connections

Guides connecting projectors to VCRs, video cameras, and other AV equipment.

HDMI Connection

Details connecting equipment with an HDMI terminal for video and audio input.

Computer Connections

Explains connecting projectors to computers via Mini D-SUB or other interfaces.

Preparation and Setup

Initial Setup Steps

Covers initial setup steps like connecting power and removing the lens cap.

Projection Angle Adjustment

Describes how to adjust the projector's angle for optimal projection.

Basic Operation

Power On and Off Procedures

Step-by-step guide for turning the projector on and off safely.

Image Positioning and Volume

Adjusts image position and audio output volume from the projector's speaker.

Aspect Ratio and 3 D Viewing

Changes aspect ratio and provides instructions for enjoying 3D content.

Menu Operation

Navigating Projector Menus

Explains the general procedure for navigating and using the projector's menus.

Picture and Video Settings

Adjusts image quality settings like brightness, contrast, color, sharpness, and tint.

Signal and Audio Settings

Configures signal input settings and manages audio input/volume.

Installation, Option, and Info Settings

Configures installation, general options, and displays projector status information.

Network Configuration

Sets up network connectivity, projector name, and IP configuration.

Image Adjustment

Brightness, Contrast, and Color Adjustment

Fine-tunes image brightness, contrast, color temperature, and tint.

Sharpness and Color Management

Controls image clarity and adjusts individual color tones (R, G, B, etc.).

Computer Image and LPF Adjustment

Adjusts computer images and applies a filter to reduce noise.

Network Settings

Projector Name and Certification

Assigns a name and configures network certification for the projector.

IP Configuration

Configures network IP address, subnet mask, gateway, and DHCP settings.

Wireless Network Setup

Sets up wireless network connection parameters like SSID and encryption.

Advanced Display Utilities

USB Display

Projects computer images directly via a USB connection without drivers.

LAN Display

Projects computer images over LAN, supporting remote desktop and multi-computer display.

PC Less Presentation

Projects images/presentations directly from USB memory without a PC.

Advanced Features

Startup Image and Freeze;Magnify

Sets custom startup images and uses freeze/magnify functions for viewing.

Password Lock Function

Enables a password to prevent unauthorized operation or access.

Computer Control

Supervises and controls the projector via a LAN network using specific software.

Lamp Replacement

Lamp Replacement Procedures

Step-by-step guides for replacing the projector lamp and resetting its operation time.

Lamp Replacement Interval

Guidance on when to replace the projector lamp based on usage hours and indicators.

Troubleshooting

Power and Image Display Issues

Solves problems related to power, no image, or incorrect image display.

Image Quality and Other Problems

Addresses image quality issues and other operational problems like noise or remote control issues.

Maintenance and Cleaning

Procedures for cleaning the projector, lens, and general maintenance warnings.

Indicators

Indicator Status and Solutions

Explains the meaning of projector indicator lights and their corresponding troubleshooting steps.

Specifications

Connector and Accessory Details

Details the types and pin configurations of connectors and lists included accessories.

RGB Signal Compatibility

Provides detailed compatibility information for RGB signals and resolutions.

Mitsubishi WD570U Specifications

General

Projection distance	- m
Vertical scan range	50 - 120 Hz
Horizontal scan range	15 - 105 kHz
Projection technology	DLP
Contrast ratio (typical)	3000:1
Screen size compatibility	40 - 300 \
Projector native resolution	WXGA (1280x800)
Aspect ratio	-
Compatibility	PC/MAC Compatibility
Dimensions (WxDxH)	259 x 111.76 x 325.12 mm
Focus	Manual
Zoom capability	Yes
Focal length range	- mm
HDCP	No
Noise level	33 dB
Noise level (economic mode)	28 dB
Dot clock scanning frequency	165 MHz
Service life of light source	3000 h
Service life of light source (economic mode)	6000 h
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720i, 720p
Analog signal format system	NTSC 4.43, PAL, SECAM B
Product color	White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	- W
Power consumption (typical)	340 W