What to do if Mitsubishi EX240U Projector does not turn on?
If your Mitsubishi Projector isn't turning on, first, ensure the power cord is securely plugged into both the projector's AC inlet and a functioning power outlet, and that the outlet switch is on, if applicable. Also, if the projector was recently turned off, wait for the cooling process to complete before attempting to turn it on again.
Why Mitsubishi Projector has no picture?
If your Mitsubishi Projector displays no picture, several factors could be at play. Ensure the video source is both turned on and correctly connected. Verify that the projector is properly connected to the input signal device and that the correct input signal is selected using the SOURCE key on the projector or remote. Also, make sure the lens cover is open.
How to fix blurred image on Mitsubishi EX240U Projector?
To correct a blurred image on your Mitsubishi Projector, start by adjusting the focus of the lens using the focus ring. Next, ensure that the projector and the screen are properly aligned by adjusting the projection angle, direction, and the unit's height if needed. Finally, verify that the lens cover is open.
What to do if Mitsubishi EX240U Projector remote control does not work?
If the remote control for your Mitsubishi Projector isn't working, try these steps: * Replace the battery with a new one. * Remove any obstacles between the remote control and the projector. * Ensure you are within 8 meters (26 feet) of the projector.
General| Matrix size | 0.55 \ |
|---|---|
| Projection distance | 1.7 - 10.5 m |
| Vertical scan range | 48 - 85 Hz |
| Horizontal scan range | 31 - 92 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 2000:1 |
| Screen size compatibility | 40 - 300 \ |
| Projector native resolution | XGA (1024x768) |
| Power LED | Yes |
| Aspect ratio | 16:9 |
| RS-232 ports | 1 |
| Dimensions (WxDxH) | 282 x 229 x 94 mm |
| Connectivity technology | Wired |
| Maximum digital resolution | 786432 pixels |
| Focus | Manual |
| Throw ratio | 1.9 - 2.1:1 |
| Focal length range | - mm |
| Noise level | 34 dB |
| Noise level (economic mode) | 29 dB |
| Dot clock scanning frequency | 170 MHz |
| Lamp power | 185 W |
| Light source type | Lamp |
| Lamp power (economic mode) | 160 W |
| Service life of light source | 3000 h |
| Service life of light source (economic mode) | 4000 h |
| DVI port | No |
| Composite video in | 0 |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Component video (YPbPr/YCbCr) in | 2 |
| Supported video modes | 1080i, 1080p, 480i, 480p, 576i, 576p, 720p |
| Analog signal format system | NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM |
| Supported graphics resolutions | 1200 x 1600, 1024 x 768 (XGA), 640 x 480 (VGA) |
| RMS rated power | 2 W |
| Placement | Ceiling |
| Product type | Standard throw projector |
| Product color | White |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | - W |
| Power consumption (typical) | 315 W |
| Cables included | VGA |
Weight and Dimensions| Weight | 2400 g |
|---|
Guides users on determining projector placement for a specific screen size.
Helps users select the appropriate screen size based on the projector's distance.
Instructions for connecting devices via HDMI for high-quality digital video.
Guides users through the process of powering on and initiating the projector.
Explains how to set, change, and recall the projector's password for security.
How to correct trapezoidal image distortion caused by non-perpendicular projection.
Describes the different aspect ratio settings available for various input signals.
Choosing predefined picture modes to suit different viewing environments and signal types.
How to create and save custom picture settings for PC (User 1) and Video (User 2).
Detailed adjustments for Brightness, Contrast, Color, Tint, Sharpness, and BrilliantColor™ in user modes.
Proper procedures for turning off the projector, including cooling down.
Items needed and steps to watch 3D content, including setting the 3D option.
Steps to set up network control via LAN, including DHCP and static IP configurations.
How to control the projector using a web browser over a local network.
How the projector calculates and displays lamp usage hours.
Settings like Lamp Mode (Low) and Auto Power Off to maximize lamp lifespan.
Displays and messages indicating when the projector lamp needs replacement.
Step-by-step instructions for safely replacing the projector lamp.
How to reset the lamp timer after replacing the lamp to track new lamp usage.
Remedies for common causes when the projector fails to power on.
Solutions for issues related to image display, focus, or alignment.
To Next Page