Monitor Audio Gold W15 - Leo; Selecting the Presets

Setting the EQ Using the Remote
With the Gold W15 powered up and out of standby mode, follow
UIFOFYUTUFQTUPTFUUIF&2
1. Press the RIGHT arrow 3 times. The display will change
to /3) then 3+$ then (4
2. Press ENTER. The display will change to show the
current setting, eg. 2))
3. 1SFTTUIF61%08/BSSPXTUPBEKVTUUIFTFUUJOH
4. 1SFTT&/5&3UPTFMFDUBOETBWF5IFEJTQMBZXJMMˍBTI
UXJDFUPDPOˌSNTFMFDUJPOBOEUIFOEJTQMBZ(4
Setting the EQ Using the Control Panel
Encoder
With the Gold W15 powered up and out of standby mode, follow
UIFOFYUTUFQTUPTFUUIF&2
1. Press the encoder down. The display will change to /3)
2. Rotate the encoder 2 positions to the right. 3+$ then
(4will be displayed
3. 1SFTT UIF FODPEFS BHBJO UP FOUFS UIF &2 NFOV  5IF
display will change to show the current setting, eg. 2))
4. Rotate the encoder left or right to change the setting
5. Press the encoder to select and save. The display will
ˍBTIUXJDFUPDPOˌSNTFMFDUJPOBOEUIFOEJTQMBZ(4
LEO
"GUFSUIFSPPNDPSSFDUJPOIBTCFFOSVOSFGFSUPQBHFJUDBO
then be enabled/ disabled within the menu:
Setting the LEO Using the Remote
With the Gold W15 powered up and out of standby mode, follow
UIFOFYUTUFQTUPTFUUIF-&0
1. Press the RIGHT arrow 3 times. The display will change
to 3+$ then (4 then /(2
2. Press ENTER. The display will change to show the
current setting, eg. 2Q
3. 1SFTTUIF61%08/BSSPXTUPBEKVTUUIFTFUUJOH
4. 1SFTT&/5&3UPTFMFDUBOETBWF5IFEJTQMBZXJMMˍBTI
UXJDFUPDPOˌSNTFMFDUJPOBOEUIFOEJTQMBZ/(2
Setting the LEO Using the Control Panel
Encoder
With the Gold W15 powered up and out of standby mode, follow
UIFOFYUTUFQTUPTFUUIF-&0
1. Press the encoder down. The display will change to 3+$
2. Rotate the encoder 2 positions to the right. (4 then
/(2 will be displayed
3. 1SFTT UIF FODPEFS BHBJO UP FOUFS UIF -&0 NFOV5IF
display will change to show the current setting, eg. 2Q
4. Rotate the encoder left or right to change the setting
5. Press the encoder to select and save. The display will
ˍBTIUXJDFUPDPOˌSNTFMFDUJPOBOEUIFOEJTQMBZ/(2
4BWJOHZPVS4FUUJOHT
0ODFZPVIBWFCFFOUISPVHIUIFNFOVUIFDIPTFOTFUUJOHTDBO
UIFOCFTBWFEUPPOFPGUIFQSFTFUTQFSJOQVU5IJTDBOCF
done by either the remote or the encoder:
4BWJOHZPVS4FUUJOHT6TJOHUIF3FNPUF
With the Gold W15 powered up, out of standby mode, the
desired input selected, and the system set up using the guides
previously, follow the next steps to save the settings:
1. 1SFTTBOEIPME1PS UIFBQQSPQSJBUFQSFTFUOVNCFS
on the remote for 3 seconds. The display will change
to 6(W
2. The display will then change to show the preset number,
eg. . Then back to the default display “ . “
4BWJOHZPVS4FUUJOHT6TJOHUIF$POUSPM
Panel Encoder
With the Gold W15 powered up and out of standby mode, the
system set up using the guides previously, follow the next
steps to save the settings:
1. Press and hold the encoder down for 3 seconds. The
display will change to 35H
2. Rotate the encoder left or right to show the current
Preset location. eg. 
3. Rotate the encoder left or right again to change the
Preset location, press and hold for 3 seconds to store.
The display will show 6(W
4. 5IFEJTQMBZXJMMˍBTIUXJDFXJUIUIFQSFTFUOVNCFSUP
DPOˌSNTFMFDUJPOBOEUIFOCBDLUPUIFEFGBVMUEJTQMBZ
“ . “
Selecting the Presets
*G B OVNCFS PG EJˋFSFOU QSFTFUT IBWF CFFO TUPSFE GPS FBDI
input, they can be recalled by following these steps:
Selecting a Preset Using the Remote
With the Gold W15 powered up and out of standby mode, the
system set up using the guides previously, follow the next
steps to recall a preset:
(PME80XOFST.BOVBM10