Monitor Audio Gold W15 - Night Mode; Auto on

1. 1SFTT 1 PS UIF BQQSPQSJBUF QSFTFU OVNCFS PO UIF
remote. The display will change to SU(
2. The display will then change to show the preset number,
eg. . Then back to the default display “ . “
Selecting a Preset Using the Control
Panel Encoder
With the Gold W15 powered up and out of standby mode, the
system set up using the guides previously, follow the next
steps to recall a preset:
1. Press and hold the encoder down for 3 seconds. The
display will change to 35H
2. Rotate the encoder left or right to show the current
Preset location. eg. 
3. Rotate the encoder left or right again to change the
Preset number and press to select
4. 5IF EJTQMBZ XJMM ˍBTI UXJDF UP DPOˌSN TFMFDUJPO BOE
then back to the default display “ . “
Night Mode
Night Mode enables the user to limit the output of the Gold
8 XJUIPVU TBDSJˌDJOH BOZ PG UIF QFSGPSNBODF  5IJT JT
CFOFˌDJBMFTQFDJBMMZXIFOTUJMMXBOUJOHUIFTVCUPCFPOBOE
audible at low levels, but don’t want the full impact from some
of the more intense parts of a sound track.
NOTE: This feature can only be controlled by the remote.
Controlling the Night Mode Using the Remote
With the Gold W15 powered up and out of standby mode, follow
the next steps to enable/ disable the auto on feature:
1. 5P UVSO OJHIU NPEF 0/ QSFTT UIF /JHIU .PEF CVUUPO
POUIFSFNPUFSFGFSUPQBHF5IFEJTQMBZXJMMTIPX
21BOEUIFODIBOHFUPopBGUFSTFDPOET5IJTJTUIF
default display when in night mode
2. 5PUVSOOJHIUNPEF0''QSFTTUIF/JHIU.PEFCVUUPOPO
UIFSFNPUFSFGFSUPQBHF5IFEJTQMBZXJMMTIPX2II
BOEUIFODIBOHFUPopBGUFSTFDPOET
Auto On
5IF BVUP PO GFBUVSF FOBCMFT UIF (PME 8 UP UVSO Pˋ PO
BVUPNBUJDBMMZPSUPCFNBOVBMMZDPOUSPMMFE 8IFO"VUP0O
mode is enabled, the user looses the ability to turn the Gold
8 Pˋ JOUP 4UBOE #Z NPEF BOE JU XJMM CF GVMMZ BVUPNBUJD
JOPQFSBUJPO8JUI"VUP0ONPEF UVSOFE 0''UIF(PME8
becomes completely manually operated. It will not turn on or
PˋXIFOBTJHOBMJTTFOTFEPSSFNPWFE
NOTE: This feature can only be controlled by the remote.
Enabling the Auto On Feature Using the
Remote
With the Gold W15 powered up and out of standby mode, follow
the next steps to enable/ disable the auto on feature:
1. 1SFTTUIFo"VUP0/pCVUUPOPOUIFSFNPUF5IFEJTQMBZ
will show the current setting. eg. 21
2. 1SFTTUIFo"VUP0/pCVUUPOBHBJOUPUVSOUIFGFBUVSFPˋ
The display will then change to 2))
%JTQMBZ$POUSPM
If the display is considered too bright for the environment, it
DBOCFFJUIFSEJNNFEPSUVSOFEPˋDPNQMFUFMZ5IFPQUJPOT
BWBJMBCMFBSF 0O0ˋBOE %JNUIFTFBSFDZDMFEUISPVHI CZ
using the remote and are continuously looped.
NOTE: This feature can only be controlled by the remote.
$POUSPMMJOH UIF %JTQMBZ #SJHIUOFTT
Using the Remote
With the Gold W15 powered up and out of standby mode, follow
the next steps to enable/ disable the auto on feature:
1SFTTUIFEJTQMBZCVUUPOSFGFSUPQBHFUPDZDMFUISPVHIUIF
options. The display brightness will change as the button is
pressed.
NOTE: *G5IFEJTQMBZJTTFUUPPˋBOEZPVXJTIUPDIBOHFTPNF
features, volume, preset, etc, the display will illuminate and
XJMMTUBZJMMVNJOBUFEGPS TFDPOET BGUFS UIFˌOBMCVUUPOJT
pressed.
'BDUPSZ3FTFU
To return the product to it’s factory settings and to erase the
memory, a Master Restore can be performed. This is achieved
by:
1. 5VSOJOHUIFTVCXPPGFSPˋBUUIFNBJOTQPXFSTXJUDI
2. Hold down the encoder, and turn the power back on at
the same time.
3. Keep the encoder pressed for 5 seconds, until the
EJTQMBZˍBTIFT3&4UISFFUJNFTJGUIFGBDUPSZSFTFUIBT
been successful.
11monitoraudio.com
ENGLISH