Monitor Audio Gold W15 - Set up; Initial Settings Using an AV Processor;Receiver

Set Up
0ODFJOQPTJUJPOBOEDBCMFTIBWFCFFOSPVUFEOPMPOHFSUIBO
NFUSFTUPBWPJEJOUFSGFSFODFDPOOFDUUIFNUPUIF(PME
W15. Mains power cable should be connected last. Do not play
any music at this stage.
NOTE: The entire set up procedure can be done via the control
panel or remote control handset.
NOTE: The Gold W15 automatically switches between inputs.
There is no option to do this manually. The LFE input will take
priority over the Stereo input. The display will show either
/)( or 6W(BTQBSUPGUIFQPXFSDZDMFTFFCFMPX
NOTE: There are 3 memory locations for user settings for each
input. Please refer to page 10.
'BDUPSZ4FUUJOHT
The default settings are:
LPF:I[TUFSFPJOQVUPOMZ
Slope Angle:E#0DUBWFTUFSFPJOQVUPOMZ
Phase: 0 degrees
EQ:0ˋ
LEO: 0ˋ
7PMVNFE#/PUFUIJTJTBMPXTFUUJOHBOETIPVMECFTFUUP
E#CFGPSFDPOˌHPSJOH
These should be treated as the initial setting when setting up
ZPVSQSPEVDU'VSUIFSˌOFUVOJOHPGUIFTFUUJOHTDBOCFEPOFJG
you feel these factory settings do not match your environment
or tastes.
1PXFS$ZDMF
The Gold W15 can be powered up using either the encoder, the
remote, or fully automatically. It will go through the following
sequence:
Press Encoder/ press Power button on remote/ receive signal
> display shows 21 for 2 seconds > the input for 5 seconds,
eg /)( > then the selected preset for 3 seconds, eg 1 > Then
UIFEFGBVMUPQFSBUJOHTDSFFOJTEJTQMBZFETJOHMFEPUJOUIF
DFOUSFPGUIFEJTQMBZ
If no signal is received for 10 minutes, it will go back into
standby mode. If the power button on the remote is pressed it
will enter standby mode. In both cases the display will show
2)) for 10 seconds and then display nothing.
Initial Settings Using an AV Processor/
Receiver
$POOFDUBTJOHMFJOUFSDPOOFDUDBCMFOPMPOHFSUIBONFUSFT
GSPNBO"7QSPDFTTPSSFDFJWFSUPUIFDPOOFDUJPONBSLFE-'&
JOQVU*GZPVIBWFBOBEEJUJPOBMTVCXPPGFSUIF-'&0VUDBOCF
used to supply the signal.
6TJOHUIF-'&JOQVUOFHBUFTUIF(PME8nTDSPTTPWFSˌMUFS
5IJTOFFETUPCFTFUPOUIF"7QSPDFTTPSSFDFJWFS1MFBTFSFGFS
to the product user manual for further information. As a guide,
the crossover should be set up in accordance with the low
GSFRVFODZMJNJUPGUIFNBJOTQFBLFSTTFFUBCMFPOQBHF
#FGPSFSVOOJOHUIFBVUPTFUVQPOUIF"7QSPDFTTPSSFDFJWFS
SFGFS UP UIF "7FRVJQNFOUnT PXOFSTNBOVBMDBSSZ PVUUIF
following initial steps:
q 3VOUIF-&0SPPNFRVBMJTFS1BHF
q 4FUUIFWPMVNFUPE#1BHF
q 1IBTFUP1BHF
q &2UP0''1BHF
q -&0UP0/ 1BHF-FPUVSOT PO BVUPNBUJDBMMZBGUFS
calibration
When the above settings have been made, you can run the
BVUPTFUVQPGUIF"7BNQMJˌFS'VSUIFSQFSTPOBMJTBUJPOBOE
adjustment can be made after the auto set up has been run by
BEKVTUJOHUIF&2*UJTBMTPTVHHFTUFEUIBUUIFTFUUJOHTPGUIF
auto set up are checked against our recommended settings
depending on the rest of your system. Do not be afraid to
BEKVTUUIFNPOZPVS"7FRVJQNFOU
7monitoraudio.com
ENGLISH