Need help?Do you have a question about the mr. steam MS-SUPER 2E and is the answer not in the manual?
General safety guidelines, including warnings about children and steam exposure.
Risks associated with steam temperature, humidity, and impact on pregnant women or those with health conditions.
Warnings about exiting immediately if uncomfortable, avoiding prolonged heat exposure, and medical conditions.
Advisories to use care when entering/exiting the steam room due to slippery floors.
Process to calculate steam room volume, including adjustments for materials and height.
Chart detailing specifications for different Mr.Steam generator models, including room volume capacity.
Crucial information for safe and proper installation and operation of the steambath generator.
Guidelines for steam room enclosure, materials, doors, flooring, and ceiling height.
Guidance on where to install the steam generator, avoiding freezing, moisture, and flammable materials.
Recommendations for clearances, unions, and control placement for optimal installation.
Instructions for installing and connecting multiple MS Super series steam generators using an interconnecting cable.
Instructions for connecting the water supply line, including pressure and valve requirements.
Guidelines for drain valve, steam outlet piping, and steam line insulation.
Requirements for safety valve installation and recommendations for using a drain pan.
Guidance on locating the steam head and initial installation steps, including avoiding hot surfaces.
Instructions for connecting the steam line and securing the steam head assembly to the wall.
Visual representation of the generator with key dimensions and connection ports clearly labeled.
Specification of NPT sizes for water inlet, steam outlet, safety valve, and drain valves.
Instructions for qualified electricians regarding power voltage, wiring, grounding, and circuit breakers.
Illustrative diagrams for connecting power supply to the steam generator models.
Wiring schematic for single phase MS 90E through MS 400E models with eTempo controls.
Wiring schematic for single phase MS Super 1E through 3E models with eTempo controls.
Installation steps for connecting multiple MS Super 4E, 5E, and 6E generators, including their interconnecting cable.
Wiring schematic for single phase MS Super 4E, 5E, and 6E models.
Diagram and instructions for connecting more than two steam generators in tandem using an optional cable.
Procedures for initial startup, testing, and checking the generator's operation after installation.
Explanation of system status codes displayed by the control, their probable causes, and suggested remedies.
Information on the AutoFlush system's function, contents, and detailed installation instructions.
Guidance on using sweat fittings and procedures to check the AutoFlush system's operation.
Details on the optional drain pan for leak protection and the Express Steam feature for faster steam.
Explanation of the LED indicators on the Liquid Level Control Board and the function of the test button.
Illustration of internal components for MS Regular Models, including access and connection points.
Illustration of internal components for MS Super Models, showing key parts and connections.
Comprehensive list of replacement parts with part numbers and applicable models.
Details on what is included in the eTEMPO control package and dimensional information.
Important notes and cautions regarding the installation of the eTEMPO control unit.
Guidance on selecting the control location and ensuring steam generator compatibility and serial number.
Instructions for drilling holes and routing the control cable from the cutout to the steam generator.
Procedures for connecting the control, powering up, and testing its functionality.
Instructions for preparing the surface, applying silicone, and mounting the eTEMPO control unit to the wall.
Guidelines for positioning the remote temperature probe within the steam room for accurate readings.
Instructions for drilling a hole, removing a knock-out, and connecting the probe cable to the generator's circuit board.
Instructions for routing the probe cable through the wall and applying silicone for a moisture seal.
Guidance on correctly exposing the temperature bulb for accurate sensing and avoiding obstructions.
Instructions for connecting the Genie Interface Module and mounting it in a suitable location.
Steps to verify the correct connection and operation of the Steam Genie Interface Module and its lights.
Procedures for pairing the Steam Genie remote with the interface module and changing addresses.
Troubleshooting guide for common issues, including remote control problems and error conditions.
Tips for cleaning and maintaining the eTEMPO controls and steamheads using mild soap and water.
Safety guidelines for using eTEMPO controls and basic maintenance procedures for the steam generator.
Instructions for operating the eTEMPO control, including turning steam on/off, pausing, and timer features.
Guidance on setting the desired temperature and switching between Fahrenheit and Celsius units.
Instructions for powering up the unit, basic ON/OFF operation, and setting the clock time.
How to set the steam duration and view the current clock time on the eTEMPO/PLUS control.
How to adjust temperature, change units, and utilize memory features for preferred settings.
Instructions for programming preferred settings (PROG I/PROG 2) and operating the AromaSteam feature.
Guidelines and cautions for using essential oils with the AromaSteam steamhead for aromatherapy.
Step-by-step instructions for replacing the battery in the Steam Genie remote control.
Instructions on how to use the Steam Genie remote to control the steam generator and interpret indicator lights.
Explanation of the status LEDs on the Genie Interface Module and their meaning for generator operation.
To Next Page
General