Flush a minimum of two-three hours after the
control has been turned off to insure that the water has cooled.
Draining immediately after a steam cycle may
expose PVC and other piping to high temperature water. Check local
codes. The unit will refill automatically when the control is activat-
ed again. In areas of hard water, a Mr.Steam AutoFlush system is
recommended for generator longevity.
Do not route eTEMPO/Plus, eTEMPO or
STEAM GENIE control wiring inside conduit together with power
lines or in proximity to hot water or steam piping. Doing so may
result in an inoperative or hazardous installation.
Do not alter or modify eTEMPO/Plus, eTEMPO, or STEAM GENIE
controls. Doing so may result in an inoperative or hazardous
installation.
IMPORTANT NOTES:
If a eTEMPO/PLUS control is to be used with a eTEMPO/REMOTE
control the eTEMPO/PLUS must be in located for “line of sight”
operation with the eTEMPO/REMOTE control. See the
eTEMPO/REMOTE operating instructions before installation of
the eTEMPO/PLUS control.
IMPORTANT:
Do not operate any eTEMPO/PLUS, eTEMPO or STEAM GENIE
controls with other than a MrSteam eTEMPO compatible steam
generator. MrSteam residential steam generators with serial num-
bers lower than 900000, or any other brand of steam generator
are not to be operated with eTEMPO controls. Doing so may
result in an inoperative installation.
This document contains important safety, operation and mainte-
nance information. Leave this document with the homeowner. Do
not discard this document.
Discontinue use of the steam generator or control if the steam
generator is damaged or otherwise not functioning properly.
Doing so may result in an inoperative or hazardous installation.
Maintenance
Mr.Steam steambath generators require little maintenance.
Other than periodic draining, maintenance procedures are
minimal. Every 2 months, or more often in “hard” water areas,
the manual drain valve should be opened fully flushing out
accumulated materials, salts and other particles which are
natural by-products of boiling water.
mr
.
steam
®
steamtherapy
®
eTEMPO
®
controls
24
1. Use only mild soap and water on a soft cloth to clean the control.
2. Do not use abrasive cleansers
3. If the decorative cover is damaged on the eTEMPO
®
or eTEMPO/
PLUS
®
call Mr.Steam technical service for replacement parts.
NOTE: Replacement of the decorative covers requires removal and
reinstallation of the control from the mounting surfaces.
Safety and Operating Information
Set the steambathing temperature accord-
ing to personal preference, however it is highly recommended
to begin steambathing at a low temperature setting to gauge
comfort and safety levels. Set the duration at 10 minutes max.
to gauge comfort and safety levels. This will allow the steam
generator to heat up and begin producing steam.
Do not install or use any eTEMPO/PLUS
®
, eTEMPO
®
or STEAM
GENIE
®
controls without reading and understanding the
Mr.Steam steam generator Installation and Operation Manual
(PN 101289 Revision number 10.0/08 or higher). Failure to read
and understand these instructions may result in an inoperative
or hazardous installation.
A peel-off warning label has been provided in the Information
envelope This label is to be applied to the wall of the installed
shower or steam enclosure.
Install the eTEMPO or eTEMPO/Plus controls according to instal-
lation instructions. Failure to install according to instructions
will result in an inoperative control or hazardous overheating or
inadequate heating of the steam room.
If a eTEMPO or eTEMPO/Plus control is installed outside the
steam room a Remote Temperature Probe (PN MSTS) must be
installed inside the steam room per installation instructions
supplied with the Remote Temperature Probe. Failure to install
according to instructions will result in an inoperative control
and overheating of the steam room.
!
WARNING
!
WARNING
homeowner
!
CAUTION
!
CAUTION
eTEMPO
®
CONTROLS
Care Tips for all Controls and Steamheads
To Next Page
Loading...
