MTS Sensors Temposonics G Series - Frequently Ordered Accessories; Installation; Measuring Range; Mounting Instructions

10
Temposonics
®
GTE Analog ATEX / NEC / CEC
Operation Manual
4.4 Frequently ordered accessories
5.1 Measuring range
All the technical data of each Temposonics
®
sensor are checked and
recorded at the nal quality inspection. At the same time the active
electrical stroke is programmed.
NOTICE
On all sensors, the areas left and right of the active stroke length are
provided for null and dead zone. These zones should not be used for
measurement, however the active stroke length can be exceeded.
Magnet
Active stroke length 63.5
(2.5)
Reference edge of mounting
Start/Null
position
37.5
(1.48)
End
position
Fig. 5: Null zone, active stroke length, dead zone
5. Installation
5.2 Mounting instructions
1. O-ring and back-up ring have been fitted at the factory.
2. Lubricate O-ring and back-up ring before mounting into
the cylinder.
3. Push the sensor into the seat carefully. Make sure that the cables
and conductors are not under strain.
4. Carefully route the cables through the cylinder wall.
Avoid tensile stress acting on the connecting cable.
5. Never expose the connecting cable to tensile stress and protect it
against sharp edges. Sharp edges could damage the insulation of
the connecting cables.
6. The bending radius of the cable must not be less than
25 mm (0.98 in.)
7. Terminate the wires on the controller side per the electrical
connection table (refer to chapter 4.3, Fig. 4) regularly.
Position magnets Magnet spacer
Ø 32.8
(Ø 1.29)
Ø 23.8
(Ø 0.94)
Ø 13.5
(Ø 0.53)
Ø 4.3
(Ø 0.17)
60°
140°
3
(0.12)
7.9
(0.31)
Ø 32.8
(Ø 1.29)
Ø 23.8
(Ø 0.94)
Ø 13.5
(Ø 0.53)
Ø 4.3
(Ø
0.17)
7.9
(0.31)
Ø 25.4
( Ø 1)
Ø 13.5
( Ø 0.53)
7.9
(0.31)
Ø 14.3
(Ø 0.56)
Ø 23.8
(Ø 0.94)
Ø 31.8
(Ø 1.25)
Ø 4.3
(Ø 0.17)
3.2
(0.13)
U-magnet OD33
Part no. 251 416-2
Ring magnet OD33
Part no. 201 542-2
Ring magnet OD25.4
Part no. 400 533
Magnet spacer
Part no. 400 633
Material: PA ferrite GF20
Weight: Approx. 11 g
Surface pressure: Max. 40 N/mm
2
Fastening torque for M4 screws: 1 Nm
Operating temperature:
−40…+105 °C (−40…+221 °F)
Material: PA ferrite GF20
Weight: Approx. 14 g
Surface pressure: Max. 40 N/mm
2
Fastening torque for M4 screws: 1 Nm
Operating temperature:
−40…+105 °C (−40…+221 °F)
Material: PA ferrite
Weight: Approx. 10 g
Surface pressure: Max. 40 N/mm
2
Operating temperature:
−40…+105 °C (−40…+221 °F)
Material: Aluminum
Weight: Approx. 5 g
Surface pressure: Max. 20 N/mm
2
Fastening torque for M4 screws: 1 Nm
Programming tool
Hand programmer for analog output
Part no. 253 853
Easy teach-in-setups of stroke length
and direction on desired zero / span
positions. For sensors with 1 magnet.
Controlling design dimensions are in millimeters and measurements in ( ) are in inches
– Additional options available in our Accessories Guide
551444
Controlling design dimensions are in millimeters and measurements in ( ) are in inches