Need help?Do you have a question about the N-Tron 708FX2 and is the answer not in the manual?
Connects the unit to the network using RJ45 and fiber optic cables.
Configures port operation as half duplex, full duplex, or auto-negotiation.
Mirrors Ethernet frames transmitted and received on other ports.
Groups network ports to increase bandwidth and provide redundant connections.
Manages resource reservation for different applications and data flows.
Allows logical grouping of devices for easier network administration.
Supports IEEE 802.1D-2004 for active network topology and faster convergence.
Configures up to 5 trap stations for sending SNMP traps.
Provides intelligent network support for multicast applications by reducing traffic.
Proprietary ring technology for expanded ring size and fault diagnostics.
Redundantly couples N-Ring topologies to other topologies.
Provides switch information access to PLCs and HMIs via standardized protocol.
Dynamically configures network parameters for hosts.
Automatically obtains IP assignment from a DHCP Server.
Allows communication between clients and servers across subnets and VLANs.
Allocates network addresses and delivers configuration parameters.
Layer 2 discovery protocol to advertise device capabilities.
Restricts access by learning or manually entering authorized MAC addresses.
Accesses the switch's web management feature via IP address.
Sets IP Address, Subnet Mask, and Gateway via DHCP or Static Mode.
Lists IP addresses for SNMP traps and community names.
Configures notifications for Power, N-Ring, N-Link, or Port Usage faults.
Defines DHCP server settings like profiles, pools, and broadcast options.
Creates IP mappings (dynamic, static) for clients and relay agents.
Lists and manages DHCP client IP address bindings.
Configures DHCP relay agent status and port settings.
Sets LLDP mode, intervals, and notification parameters.
Configures LLDP transmit, receive, and management data settings per port.
Displays LLDP neighbor information, including MAC, IP, and VLAN details.
Shows LLDP frame counts (transmitted, received, discarded, errors).
Configures port settings like admin status, speed, duplex, and QoS.
Controls port security modes (learning or locked) and authorized MAC addresses.
Allows manual entry or deletion of authorized MAC source addresses.
Logs unauthorized MAC addresses that attempted device access.
Configures port mirroring to monitor traffic on selected ports.
Groups network ports for increased bandwidth and redundancy.
Configures QoS priorities based on DSCP, 802.1p, or port-based priority.
Displays MIB parameters and packet counters for each port.
Shows bandwidth usage percentage per port as a bar graph.
Configures VLANs, including replacing VID tags and ingress filtering.
Configures VLAN groups, port membership, and egress tagging.
Displays and modifies the aging time for MAC addresses.
Lists and allows static assignment of MAC addresses to ports.
Lists and allows static assignment of multicast group addresses to ports.
Shows MAC addresses and associated IP addresses found on each port.
Displays RSTP information and allows configuration for each VLAN.
Configures IGMP status, query mode, router mode, and manual router ports.
Configures the router multicast data filter for ports.
Configures N-View status and the interval between reports.
Configures N-View multicast and MIB stats reporting for ports.
Configures N-Ring mode (Auto Member, Manager) and aging time.
Configures advanced N-Ring settings for members and managers.
Displays the current N-Ring status for members and managers.
Configures N-Link mode and default coupler port.
Displays N-Link status for master, slave, and coupler switches.
Configures CIP status and requested packet intervals (RPI).
Displays CIP status, including identity and connection information.
Uploads or downloads firmware and configuration files via TFTP.
Provides contact information for N-Tron support.
Configures the broadcast packet percentage limit for each port.
Lists authorized users and allows adding new users with permissions.
Lists authorized users; allows removal via the 'Remove' button.
Saves current configuration or resets to factory defaults.
Provides basic definitions and choices for switch features.
Information on configuration options within the Administration category.
Information on configuration options within the DHCP category.
Information on configuration options within the LLDP category.
Information on configuration options within the Ports category.
Information on configuration options within the Statistics category.
Information on configuration options within the VLAN category.
Information on configuration options within the Bridging category.
Information on configuration options within the RSTP category.
Information on configuration options within the IGMP category.
Information on configuration options within the N-View category.
Information on configuration options within the N-Ring category.
Information on configuration options within the N-Link category.
Information on configuration options within the CIP category.
Information on configuration options within the Firmware/Config category.
Information on configuration options within the BPCL category.
Information on configuration options within User Management.
Information on other links and categories in the web manager.
Lists all available commands or provides help on a specific command.
Logs out of the console interface.
Manages Address Resolution Logic (ARL) entries.
Shows or sets CIP configuration status and parameters.
Saves or resets configuration settings to factory defaults.
Shows or sets IGMP configuration status and parameters.
Shows or sets port mirroring configuration.
Shows or sets N-Ring configuration mode and parameters.
Shows or sets N-View status and interval.
Pings a host to test network connectivity and latency.
Configures port settings like speed, duplex, and VLAN.
Resets or reboots the switch.
Shows or sets SNMP configuration parameters.
Displays or clears the last system error message.
Displays detailed system information, including hardware and software.
Sets or shows the system IP configuration mode and parameters.
Shows or sets system configuration parameters like name and browser access.
Shows the factory default VLAN configuration.
Demonstrates basic understanding of port-based VLANs with examples.
Explains tagged VLANs with examples allowing only tagged traffic.
Explains tagged VLANs with examples allowing all traffic.
Illustrates basic understanding of Hybrid VLANs with examples.
Demonstrates basic understanding of overlapping VLANs with examples.
Explains VLANs with multicast filtering using examples.
Details switch properties like MAC addresses, aging time, and switching method.
Specifies physical dimensions, weight, and mounting options.
Details input voltage, current, ripple, and power supply requirements.
Specifies operating temperature, humidity, and altitude.
Details shock and vibration specifications.
Provides MTBF and warranty information.
Lists connector types for ports.
Specifies recommended clearance for wiring.
Details network media requirements for different port types.
Lists characteristics for 100 Mb fiber transceivers.
Details switch properties like MAC addresses, aging time, and switching method.
Specifies physical dimensions, weight, and mounting options.
Details input voltage, current, ripple, and power supply requirements.
Specifies operating temperature, humidity, and altitude.
Details shock and vibration specifications.
Provides MTBF and warranty information.
Lists connector types for ports.
Specifies recommended clearance for wiring.
Details network media requirements for different port types.
Lists characteristics for 100 Mb fiber transceivers.
Lists safety, EMI, and EMS certifications for 708 models.
Lists safety, EMI, and EMS certifications for 716 models.
Instructions for obtaining warranty service authorization and return procedures.
Details the advance replacement option and customer responsibilities.
Disclaims other warranties and limits remedies to repair, replacement, or refund.
Excludes liability for incidental, consequential, or indirect damages.
States limitations on implied warranties and damages based on local law.
Specifies the governing law for the limited warranty.
To Next Page
General
