TABLE OF STANDBY MODE SCENARIOS
Conditions
• Control in Standby: O
• Current source before standby mode: OPTICAL1, OPTICAL2, COAXIAL1, COAXIAL2, COMPUTER, AIRPLAY, DOCK, BT, DLNA or SPOTIFY
• Remote app and D 7050 connected to the same network
SETTINGS BEFORE STANDBY MODE STANDBY MODE AFTER 30 MINUTES STATUS AFTER STANDBY MODE
(Default mode)
Auto Shuto: On
Power Save: O
Auto Sense: Enabled
IR Learning: No
Network standby mode · Switch to operating mode upon detection of active input signal from the last selected source before
going to standby mode. Power up to said last selected source.
· Wake up also to streaming services (AirPlay, DLNA or Spotify) and DOCK input. Source switches to
the particular streaming service or DOCK.
· All other inputs when their sources become active cannot activate the D 7050.
· Pressing remote app or top panel’s o (Standby) and remote control’s [ON] button will also switch
D 7050 to operating mode.
(TV Connect mode*)
Auto Shuto: On
Power Save: O
Auto Sense: Enabled
IR Learning: Yes
Network standby mode · Wake up to OPTICAL1 input signal and then automatically switches to OPTICAL 1 source.
· Wake up also to streaming services (AirPlay, DLNA or Spotify) and DOCK input. Source switches to
the particular streaming service or DOCK.
· All other inputs when their sources become active cannot activate the D 7050.
· Pressing remote app or top panel’s o (Standby) or [ON] button of either D 7050 remote control or
TV remote control will also switch D 7050 to operating mode.
Auto Shuto: On
Power Save: On
Auto Sense: Disabled
IR Learning: Yes or No
Eco standby mode · Can only be switched back to operating mode by pressing top panel’s o (Standby) or [ON] button
of either D 7050 remote control or TV remote control (with IR Learning completed).
· Remote app cannot switch back the unit to operating mode.
Auto Shuto: O
Power Save: On or O
Auto Sense: Enabled or Disabled
IR Learning: Yes or No
Remain at operating mode Remain at operating mode.
* - Refer to TV CONNECT section below.
IMPORTANT NOTES ABOUT POWER SAVE SETTINGS
• If D 7050 is switched to standby mode with POWER SAVE set to ON, the D 7050 will go to Demo Mode. At this condition, the D 7050 cannot be switched
back to operating mode using the D 7050 app. Press top panel’s o (Standby) or remote control’s [ON] button to switch back D 7050 to operating mode.
• Keep POWER SAVE setting to OFF for continuous control of D 7050 using the D 7050 app.
• AUTO SENSE is disabled when POWER SAVE is enabled/ON and vice-versa.
OTHER FEATURES
TV CONNECT
TV Connect is a new software enabled feature that allows the D 7050
to provide the sound for your TV. TV Connect enables D 7050 to learn
the mute and volume control commands from any TV remote control.
Additionally, the D 7050 will automatically power up to OPTICAL 1 source
upon detection of digital TV output signal at OPTICAL 1 input.*
With TV Connect fully integrated, you can use your TV remote control to
manage the following features of D 7050:
1 Adjust Volume up/down
2 Enable or disable MUTE function
3 Switch ON D 7050
HOW TO CONFIGURE YOUR D 7050 WITH TV CONNECT
TV Connect setup requires the digital optical output of your TV to be
connected to the OPTICAL 1 input of your D 7050. With this setup and with
proper conguration, when you turn ON your TV, the D 7050 powers up from
standby mode and the TV input (OPTICAL 1) is automatically selected.* The
D 7050 can also be awakened by pressing the top panel’s o and the power
ON button of either D 7050 remote control or TV’s remote control.
The following congurations are necessary to integrate TV Connect with
your D 7050.
• Enable auto standby mode.
• Enable auto sense mode.
• Perform IR (infrared) learning with TV remote control.
ENABLE AUTO STANDBY MODE
• Using the D 7050 App, select “SETTINGS” menu and then set “AUTO
SHUTOFF” to “ON”.
ENABLE AUTO SENSE MODE
• While at standby mode, press and hold “4” button of the D 7050 remote
control until o icon at the top screen wakes up and blinks once.
14
To Next Page
Loading...
