Nautilus R618 User Manual

10
Console Service Mode – x618 series Consoles
The Console Setup Mode lets you input the date and time, set the units of measurement to either English or Metric,
FKDQJHWKHPDFKLQHW\SHFRQWUROWKHVRXQGVHWWLQJVRQRႇRUVHHPDLQWHQDQFHVWDWLVWLFV7RWDO5XQ+RXUV±IRU
service technician use only).
1. To go into the Console Setup Mode:
- For the later version of the console, hold down the PAUSE/END button and Increase (c) button together for 3 sec-
onds while in the Power-Up Mode.
- For the earlier version of the console, hold down the PAUSE/END button and Left button together for 3 seconds
while in the Power-Up Mode.
Note:3XVK3$86((1'WRH[LWWKH&RQVROH6HWXS0RGHDQGUHWXUQWRWKH3RZHU8S0RGHVFUHHQ
2. The Console display shows the Date prompt with the current setting. To change, push the Increase/Decrease buttons
WRDGMXVWWKHFXUUHQWO\DFWLYHYDOXHÀDVKLQJ3XVKWKH/HIW5LJKWEXWWRQVWRFKDQJHZKLFKVHJPHQWLVWKHFXUUHQWO\
active value (month / day / year).
3. Push OK to set.
4. The Console display shows the Time prompt with the current setting. Push the Increase/Decrease buttons to adjust
WKHFXUUHQWO\DFWLYHYDOXHÀDVKLQJ3XVKWKH/HIW5LJKWEXWWRQVWRFKDQJHZKLFKVHJPHQWLVWKHFXUUHQWO\DFWLYHYDOXH
(hour / minute / AM or PM).
5. Push OK to set.
6. The Console display shows the Units prompt with the current setting. To change, push OK to start the Units option.
Push the Increase/Decrease buttons to change between “MILES” (Imperial English units) and “KM” (metric units).
Note: If the units change when there is data in User Statistics, the statistics convert to the new units.
7. Push OK to set.
8. The Console display shows the Sound Settings prompt with the current setting. Push the Increase/Decrease buttons
to change between “ON” and “OFF”.
9. Push OK to set.
10. The Console display shows the TOTAL RUN HOURS for the machine.
 7RJRWRWKHQH[W&RQVROH6HWXS0RGHSURPSWSXVKWKH2.EXWWRQ
To enter the Manufacturing Menu (MFG Menu):
- For the later version of the console, hold down the PAUSE/END button and Increase (c) button together for 3 sec-
onds while in the Power-Up Mode.
- For the earlier version of the console, hold down the PAUSE/END button and Left button together for 3 seconds
while in the Power-Up Mode.
The Console display shows the Firmware Version string. Push the Up/Down buttons to move through the MFG Menu
options. Push OK to make a selection.
D(17(50)*7(67±7KLVRSWLRQLVLQWHQGHGIRUXVHRQWKHPDQXIDFWXULQJSURGXFWLRQOLQHRQO\,WLVDFKDLQHG
series of tests similar to the tests listed below, but optimized to be run on the production line. This chained test
should not be used anywhere but on the production line.
Condition/Problem Things to Check Solution
Workout results not post-
ing from Nautilus Trainer
™
to MyFitnessPal
®
/ Under
Armour
®
Connected Fit-
ness.
Sync accounts From the Menu icon on the Nautilus Trainer™ App, select the
Sync to MyFitnessPal
®
or Under Armour
®
Connected Fitness.
Sync fails Review account and password for MyFitnessPal
®
/ Under Ar-
mour
®
Connected Fitness.
Contact appsupport@nautilus.com (if inside US/Canada)
or your local distributor (if outside US/Canada) for further
assistance.

Nautilus R618 Specifications

General

Resistance Levels	25
Bluetooth Connectivity	Yes
Workout Programs	29
Resistance Type	Magnetic
Display	LCD
Heart Rate Monitoring	Contact
Warranty	10 year frame, 1 year labor