Why is the ACT LED flashing continuously on my NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart and the network disabled?
If the ACT LED is constantly flashing on all connected ports and the network is disabled on your NETGEAR Switch, it indicates a network loop (redundant path) has been created. To resolve this, ensure there is only one path from any networked device to any other networked device, breaking the loop.
What to do if a segment or device is not recognized on NETGEAR Switch?
If a segment or device isn't recognized as part of the network when using your NETGEAR Switch, it could be due to devices not being properly connected or cabling not meeting Ethernet guidelines. Verify that the cabling is correct and ensure all connectors are securely positioned in the required ports. Also, check for accidentally disconnected equipment.
How to fix slow file transfer on NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart Switch?
If file transfers are slow or you experience performance degradation with your NETGEAR Switch, the half- or full-duplex settings on the switch and the connected device might not be the same. Ensure the attached device is set to auto-negotiate.
What to do if the Link LED is off on NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart?
If the Link LED is off or intermittent on your NETGEAR Switch, it indicates a port connection issue. Check the crimp on the connectors and ensure the plug is properly inserted and locked into the port at both the switch and the connecting device. Make sure all cables are used correctly and comply with Ethernet specifications. Test for a defective adapter card, cable, or port by testing them in an alternate environment where all products are functioning.
Why is the power LED off on my NETGEAR Switch?
If the Power LED is off on your NETGEAR Switch, it means no power is being received. Check the power cord connections for the switch at both the switch and the connected device. Ensure all cables are used correctly and comply with the Ethernet specifications.
General| PoE | Yes |
|---|---|
| PoE Power Budget | 192W |
| Switching Capacity | 12.8 Gbps |
| Forwarding Rate | 9.5 Mpps |
| MAC Address Table Size | 8K |
| VLAN Support | Yes |
| Power Supply | Internal |
| Voltage | 100-240V AC |
| Frequency | 50-60 Hz |
| Rack Mountable | Yes |
| Management | SNMP |
| Dimensions | 440 x 204 x 43 mm |
| Throughput | 9.5 Mpps |
| Jumbo Frame Support | Yes |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 70°C |
| Humidity | 90% maximum relative humidity, noncondensing |
| Ports | 24 x 10/100 Mbps |
Provides contact details for technical support and website information.
Covers trademarks, conditions of use, and regulatory statements.
Indicates compliance with R&TTE Directive and specific EU Council Directives.
Details FCC regulations, human exposure, and declarations of conformity.
Guidance on preventing and correcting radio frequency interference.
Explains typographical conventions, message formats, and manual navigation.
Provides instructions for printing pages or chapters of the manual.
Explains navigation buttons, table of contents, and search functionality.
Details printing single pages and chapters from the manual.
Introduces the NETGEAR Smart Switch and its capabilities.
Lists the key features of the NETGEAR Smart Switch.
Details the items included in the product package.
Covers site requirements and the physical installation of the switch.
Details connecting devices, installing modules, and applying AC power.
Explains how to configure the switch using a web browser or utility.
Instructions for mounting the switch on a flat surface using rubber footpads.
Step-by-step guide to rack-mounting the switch using the provided kit.
Describes the front and back panels of the FS728TP Smart PoE Switch.
Explains the meaning of various LED indicators on the switch.
Information about the physical ports and interfaces on the switch.
Details the LED indicators for each port, including link/activity and speed.
Explains the system status LEDs like Power, FAN, and MAX POE.
Details the auto-sensing RJ-45 ports and Auto Uplink technology.
Covers SFP module bays and the factory defaults reset button functionality.
Lists common symptoms, causes, and solutions for troubleshooting issues.
Provides further tips for resolving problems if the chart is insufficient.
Advice on checking network adapter cards and drivers for issues.
Guidance on troubleshooting configuration-related problems.
Steps to verify switch integrity and contact support.
Lists supported network protocols and IEEE standards.
Details management features like VLAN and QoS.
Describes the switch's physical interfaces and port types.
Lists the types of LEDs on the switch and their purpose.
To Next Page