Home
NETGEAR
Switch
GS408EPP
Page 55 (Manage Power over Ethernet)
NETGEAR GS408EPP - Manage Power over Ethernet
67 pages
Manual
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
55
6
6.
Manage P
ow
er ov
er Ethernet
This chapter covers the following topics:
•
PoE Overview
•
Device Class Power Requirements
•
Power
Allocation and Power Budget
•
Manage and View the PoE Port Configuration
•
Reset One or More PoE+ Ports
54
56
Table of Contents
Main Page
Default Chapter
3
Table of Contents
3
Chapter 1 Getting Started
5
Configure the Switch
6
Access the Switch Using a Web Browser
6
Access a Switch that Is Off-Network
6
Access a Switch Connected to a Network
7
Access the Switch with the Prosafe Plus Configuration Utility
7
Install the Prosafe Plus Utility
7
Access the Switch Using the Prosafe Plus Utility
8
Change the Password
9
Chapter 2 Network Settings
11
Specify IP Address Settings for the Switch
12
Use Browser-Based Access to Specify the Switch IP Address
12
Use the Prosafe Plus Utility to Specify the Switch IP Address
13
Manage Multicast Traffic with IGMP Snooping
14
Customize IGMP Snooping
14
Specify a VLAN for IGMP Snooping
15
Set up Link Aggregation Groups
16
Chapter 3 Optimize Performance with Quality of Service
18
Enable 802.1P/Dscp-Based Quality of Service
19
Enable Port-Based Quality of Service
20
Set up Rate Limiting
21
Set up Broadcast Filtering
22
Chapter 4 Use VLANS for Traffic Segmentation
24
VLAN Overview
25
Create a Basic Port-Based VLAN
25
Assign Ports to Multiple VLAN Groups
27
Create 802.1Q-Based Vlans in a Basic Configuration
28
Create 802.1Q-Based Vlans in an Advanced Configuration
30
Add Tagged or Untagged Ports to an 802.1Q-Based VLAN
31
Specify a Port PVID for an 802.1Q-Based VLAN
32
Manage the Voice VLAN
33
Select the Voice VLAN and Class of Service
34
Enable the Voice VLAN for Ports
35
Manage the OUI Table
36
Chapter 5 Manage and Monitor the Switch
40
Manage Flow Control
40
Manage the Port Speed
41
Specify a Port Description
42
Enable Loop Detection
43
Control the Port Leds
43
Enable the Power Saving Mode
44
Change the Switch Management Mode
45
Manage Access Control
46
Add Devices to the Access Control Table
46
Remove Devices from the Access Control Table
47
Upgrade the Firmware
48
Reboot the Switch
49
Save the Switch Configuration
49
Restore a Saved Switch Configuration
50
Restore Factory Default Settings
51
Enable Port Mirroring
52
View Switch Information
53
View Port Statistics
54
Chapter 6 Manage Power over Ethernet
55
Poe Overview
56
Device Class Power Requirements
56
Power Allocation and Power Budget
57
Manage and View the Poe Port Configuration
58
Reset One or more Poe+ Ports
61
Chapter 7 Diagnostics and Troubleshooting
62
Register Your Product
63
Test Cable Connections
63
Resolve a Subnet Conflict to Access the Switch
64
Appendix A Supplemental Information
65
Factory Default Settings
66
Technical Specifications
67
Other manuals for NETGEAR GS408EPP
Installation Guide
2 pages
Installation
2 pages
Hardware Installation Guide
30 pages
Related product manuals
NETGEAR GS316
2 pages
NETGEAR GS205
2 pages
NETGEAR GS308T
351 pages
NETGEAR GS748T
302 pages
NETGEAR GS110T
28 pages
NETGEAR GS324T
365 pages
NETGEAR GS308PP
8 pages
NETGEAR GS116LP
2 pages
NETGEAR GS116v2
2 pages
NETGEAR GS305EP
94 pages
NETGEAR GS108LP
7 pages
NETGEAR GS108PE
2 pages
To Next Page
