EasyManuals Logo

NETGEAR WG511T User Manual

NETGEAR WG511T
83 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #62 background imageLoading...
Page #62 background image
User Manual for the NETGEAR 108 Mbps Wireless PC Card 32-bit CardBus WG511T
B-6 Wireless Networking Basics
Key Size
The IEEE 802.11 standard supports two types of WEP encryption: 40-bit and 128-bit.
The 64-bit WEP data encryption method, allows for a five-character (40-bit) input. Additionally,
24 factory-set bits are added to the forty-bit input to generate a 64-bit encryption key. (The 24
factory-set bits are not user-configurable). This encryption key will be used to encrypt/decrypt all
data transmitted via the wireless interface. Some vendors refer to the 64-bit WEP data encryption
as 40-bit WEP data encryption since the user-configurable portion of the encryption key is 40 bits
wide.
The 128-bit WEP data encryption method consists of 104 user-configurable bits. Similar to the
forty-bit WEP data encryption method, the remaining 24 bits are factory set and not user
configurable. Some vendors allow passphrases to be entered instead of the cryptic hexadecimal
characters to ease encryption key entry.
128-bit encryption is stronger than 40-bit encryption, but 128-bit encryption may not be available
outside of the United States due to U.S. export regulations.
When configured for 40-bit encryption, 802.11 products typically support up to four WEP Keys.
Each 40-bit WEP Key is expressed as 5 sets of two hexadecimal digits (0-9 and A-F). For
example, “12 34 56 78 90” is a 40-bit WEP Key.
When configured for 128-bit encryption, 802.11b products typically support four WEP Keys but
some manufacturers support only one 128-bit key. The 128-bit WEP Key is expressed as 13 sets of
two hexadecimal digits (0-9 and A-F). For example, “12 34 56 78 90 AB CD EF 12 34 56 78 90”
is a 128-bit WEP Key.
Note: Typically, 802.11 access points can store up to four 128-bit WEP Keys but some 802.11
client adapters can only store one. Therefore, make sure that your 802.11 access and client
adapters configurations match.
WEP Configuration Options
The WEP settings must match on all 802.11 devices that are within the same wireless network as
identified by the SSID. In general, if your mobile clients will roam between access points, then all
of the 802.11 access points and all of the 802.11 client adapters on the network must have the same
WEP settings.

Table of Contents

Other manuals for NETGEAR WG511T

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR WG511T and is the answer not in the manual?

NETGEAR WG511T Specifications

Radio Specifications IconRadio Specifications
radio data rate1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps and 108 Mbps in turbo mode
frequency US2.412 ~ 2.462 GHz
frequency Japan2.412 ~ 2.484 GHz
frequency Europe ETSI2.412 ~ 2.472 GHz
frequency Spain2.457 ~ 2.462 GHz
frequency France2.457 ~ 2.472 GHz
Security IconSecurity
encryption40-bit (also called 64-bit) and 128-bit WEP Encryption
electromagnetic complianceFCC Part 15 Sub Class B
modulation typeOFDM with BPSK, QPSK, 16QAM, 64QAM, DBPSK, DQPSK, CCK
Physical Specifications IconPhysical Specifications
dimensions119 x 54 x 6 mm (4.68 x 2.12 x .25 in.)
weight46 g (1.6 oz)
warrantyNETGEAR 1-year warranty

Related product manuals