Item register
A
Accessibility, electrical connection, 20
Accessories, 69
Alarm, 67
Assembly, 5
B
Back button, 34
C
Cable lock, 21
Commissioning and adjusting, 31
Commissioning without heat pump, 33
Filling and venting, 31
Post-adjustment, venting, 33
Preparations, 31
Start guide, 32
Start-up and inspection, 32
Commissioning without heat pump, 33
Connecting accessories, 30
Connecting ACS 310, 16
Connecting cold and hot water, 15
Connecting current sensors, 27
Connecting EMK 300, 16
Connecting external operatingvoltage for the controlsystem, 22
Connecting pool, 17–18
Connecting the climate system, 15
Connecting to heat pump, 15
Connection as electric boiler, 15
Connection of external electrical addition, 16
Connection of external heat source, 16
Connections, 22
Contact for activation of “external adjustment", 28
Contact for activation of “temporary lux", 28
Contact for external tariff blocking, 28
Contact information, 4
Control, 34, 38
Control - Introduction, 34
Control - Menus, 38
Control - Introduction, 34
Display unit, 34
Menu system, 35
Control knob, 34
Control - Menus, 38
Menu 1 - INDOOR CLIMATE, 38
Menu 2 - HOT WATER, 47
Menu 3 - INFO, 49
Menu 4 - MY SYSTEM, 50
Menu 5 - SERVICE, 56
D
Delivery and handling, 5
Assembly, 5
Installation area, 5
Removing the covers, 6
Supplied components, 5
Transport, 5
Dimensions and pipe connections, 10
Dimensions and setting-out coordinates, 71
Display, 34
Display unit, 34
Back button, 34
Control knob, 34
Display, 34
OK button, 34
Status lamp, 34
Switch, 34
Disturbances in comfort, 67
Alarm, 67
Manage alarm, 67
Troubleshooting, 67
Draining the climate system, 31, 63
Draining the hot water heater, 63
E
Electrical addition - maximum output, 25
Power steps of the immersion heater, 25
Electrical circuit diagram, 3 x 400 V, 73
Electrical connections, 19, 24
Accessibility, electrical connection, 20
Cable lock, 21
Communication, 24
Connecting accessories, 30
Connecting external operating voltage for the control sys-
tem, 22
Connections, 22
Electrical addition - maximum output, 25
External connection options, 27
General, 19
Load monitor, 27
Miniature circuit-breaker, 19
Outdoor sensor, 23
Power connection, 22
Removing the cover, base board, 20
Removing the cover, immersion heater circuit board, 20
Removing the hatch, input circuit board, 20
Room sensor, 23
Settings, 25
Temperature limiter, 19
External connection options, 27
Contact for activation of “external adjustment", 28
Contact for activation of “temporary lux", 28
Contact for external tariff blocking, 28
Possible selection for AUX inputs, 27
Possible selection for AUX output (potential free variable re-
lay), 29
Switch for external blocking of heating, 28
Temperature sensor, cooling/heating, 27
F
Filling , 31
Filling and venting, 31
Draining the climate system, 31
Filling , 31
Filling the hot water heater, 31
Venting the climate system, 31
Filling the hot water heater, 31
H
Help menu, 32, 37
I
Important information, 2
Safety information, 2
Indoor module's design, 7
Component locations, 7
List of components, 8
Initial pressure, 9
Inspection of the installation, 3
Installation alternative, 12
Connecting ACS 310, 16
Connecting cold and hot water, 15
Connecting EMK 300, 16
Connecting pool, 17–18
Connecting the climate system, 15
Connecting to heat pump, 15
NIBE™ VVM 325Chapter 13 | Item register78
13 Item register
To Next Page
