Nice SO2000 - User Manual

Other manuals for Nice SO2000

Instructions And Warnings For Installation And Use36 pages

Questions and Answers

T
Terry BrennanAug 21, 2025
How to fix a Nice SO2000 Garage Door Opener when the remote doesn't work and the LED is off?
- B
  Brandon DoyleAug 21, 2025
  If your Nice Garage Door Opener's remote isn't working and the LED on the remote isn't lighting up, the first thing you should do is check the batteries in the transmitter. If they are exhausted, replace them with new ones.
N
Nathaniel MartinezAug 23, 2025
Why doesn't my Nice SO2000 Garage Door Opener respond to the remote, but the LED is on?
- J
  john84Aug 23, 2025
  If the LED on your Nice Garage Door Opener remote lights up, but the opener doesn't respond, the transmitter may not be correctly memorized in the radio receiver. Check whether the transmitter has been memorised correctly in the radio receiver.
T
Tiffany MarshAug 26, 2025
What to do if my Nice SO2000 Garage Door Opener doesn't start and the BlueBUS LED isn't flashing?
- N
  Natasha ToddAug 26, 2025
  If your Nice Garage Door Opener isn't starting and the “BlueBUS” LED isn't flashing, check that the gearmotor is receiving mains voltage. Also, inspect fuses F1 and F2. If they are blown, determine the cause of the failure and replace them with fuses that have the same current rating and characteristics.
F
fergusonalisonAug 27, 2025
What to do if my Nice SO2000 Garage Door Opener doesn't start and the warning light is off?
- J
  johnromeroAug 28, 2025
  If your Nice Garage Door Opener isn't starting and the warning light is off, verify that the command is actually being received. If the command reaches the Step-by-Step input, the corresponding “Sbs” LED should light up. If you're using the radio transmitter, the “BlueBus” LED should emit two fast flashes.
C
Cheryl JohnsonAug 30, 2025
Why is my Nice Garage Door Opener not responding to the remote but the LED is on?
- J
  Joseph SinghAug 30, 2025
  If your Nice Garage Door Opener radio transmitter does not control the automation, but the LED on the transmitter lights up, it might not be correctly memorised in the radio receiver. Check whether the transmitter has been memorised correctly in the radio receiver.
W
walkerchristopherSep 1, 2025
What does it mean when L1 or L8 is flashing rapidly on my Nice SO2000 Garage Door Opener?
- M
  Mike DuffySep 1, 2025
  If LED “L1” flashes rapidly on your Nice Garage Door Opener, perform a closing manoeuvre until LED “L1” stops flashing rapidly. Then detach Soon from the spring support shaft, open the door to the maximum position and re-install Soon from this position. If LED “L8” flashes, perform an opening manoeuvre until LED “L8” stops flashing rapidly. Then detach Soon from the spring support shaft, close the door to the maximum position and re-install Soon from this position.
W
wardwalterSep 3, 2025
What to do if the warning light flashes a few times on my Nice SO2000 Garage Door Opener?
- E
  Erin BowersSep 3, 2025
  If no manoeuvre starts and the warning light flashes a few times on your Nice Garage Door Opener, count the number of flashes and check the corresponding value in “Table 13”.
S
Susan ValenzuelaSep 5, 2025
What to do if my Nice Garage Door Opener starts then immediately reverses?
- J
  james55Sep 5, 2025
  If your Nice Garage Door Opener starts but immediately reverses, it could be due to a few reasons. First, check for any obstructions that might be triggering the reversal. If there are none, the selected force value might be too low for your gate. In this case, you may need to select a higher force setting. Also, verify that a safety device connected to the Stop input hasn't been activated.
M
Marc DavisSep 7, 2025
What does it mean when LED “L1” or LED “L8” is flashing rapidly on my Nice SO2000 Garage Door Opener?
- L
  Lisa AguirreSep 7, 2025
  If LED “L1” is flashing rapidly on your Nice Garage Door Opener, it means the high overrun position has been reached. Perform a closing manoeuvre until LED “L1” stops flashing rapidly. Then, detach Soon from the spring support shaft, open the door to the maximum position, and reinstall Soon from this position. If LED “L8” is flashing rapidly, it means the low overrun position has been reached. Perform an opening manoeuvre until LED “L8” stops flashing rapidly. Then, detach Soon from the spring support shaft, close the door to the maximum position, and reinstall Soon from this position.
G
grantcherylSep 10, 2025
Why isn't the warning light working on my Nice SO2000?
- M
  Mark LewisSep 10, 2025
  If the manoeuvre completes correctly on your Nice Garage Door Opener, but the warning light isn't working, first, check for voltage on the warning light’s FLASH terminal during the manoeuvre (it should be roughly 10–30 Vc). If there is voltage, replace the lamp with one having the same characteristics. If there's no voltage, there may have been an overload on the FLASH output, so check that the cable hasn't short-circuited.