What to do if my Nilfisk-ALTO Pressure Washer is scaled and the light is flashing?
If the Nilfisk-ALTO Pressure Washer is scaled and the light is flashing, refuel the detergent or set the SDR value to “0“. Turn the main switch to the “OFF“ position and let the machine cool down. Also, remove or disconnect the extension cable.
What to do if the water tap is closed for my Nilfisk-ALTO Pressure Washer and the light is flashing?
If the light is flashing and the water tap is closed or there is a water shortage for your Nilfisk-ALTO Pressure Washer, refuel the detergent or set the SDR value to “0“. Turn the main switch to the “OFF“ position and let the machine cool down. Also, remove or disconnect the extension cable.
What to do if there is a flow sensor fault on my Nilfisk-ALTO NEPTUNE 1 Pressure Washer and the light is flashing?
If the light is flashing due to a flow sensor fault in your Nilfisk-ALTO Pressure Washer, refuel the detergent or set the SDR value to “0“. Turn the main switch to the “OFF“ position and let the machine cool down. Also, remove or disconnect the extension cable.
What to do if the Nilfi sk-ALTO Anti-Stone level is low on my Nilfisk-ALTO NEPTUNE 1 Pressure Washer and the light is flashing?
If the light is flashing because the Nilfisk-ALTO Anti-Stone level is low, top up the Nilfisk-ALTO Anti-Stone.
What to do if the motor is overheated on my Nilfisk-ALTO Pressure Washer and the light is flashing?
If the Nilfisk-ALTO Pressure Washer's motor is overheated and the light is flashing, refuel the detergent or set the SDR value to “0“. Then turn the main switch to the “OFF“ position and let the machine cool down. Also, remove or disconnect the extension cable.
What to do if the detergent tank is empty on my Nilfisk-ALTO NEPTUNE 1 Pressure Washer and the light is flashing?
If the light is flashing and the detergent tank is empty on your Nilfisk-ALTO Pressure Washer, refuel the detergent or set the SDR value to “0“. Turn the main switch to the “OFF“ position and let the machine cool down. Also, remove or disconnect the extension cable.
What to do if the spray gun is leaking on my Nilfisk-ALTO Pressure Washer and the light is flashing?
If the Nilfisk-ALTO Pressure Washer spray gun is leaking and the light is flashing, refuel the detergent or set the SDR value to “0“. Turn the main switch to the “OFF“ position and let the machine cool down. Remove or disconnect the extension cable.
What to do if the high pressure hose is leaking on my Nilfisk-ALTO NEPTUNE 1 Pressure Washer and the light is flashing?
If the high pressure hose, coupling, or line system is leaking on your Nilfisk-ALTO Pressure Washer and the light is flashing, refuel the detergent or set the SDR value to “0“. Turn the main switch to the “OFF“ position and let the machine cool down. Also, remove or disconnect the extension cable.
What to do if the pressure regulation is blocking on my Nilfisk-ALTO NEPTUNE 1 Pressure Washer and the light is flashing?
If the light is flashing on your Nilfisk-ALTO Pressure Washer due to pressure regulation issues or the VarioPress lance being set to low water volume, refuel the detergent or set the SDR value to “0“. Turn the main switch to the “OFF“ position and let the machine cool down. Also, remove or disconnect the extension cable.
What to do if the fuel level is low on my Nilfisk-ALTO Pressure Washer and the light is constant?
If the light is constant and the fuel level is low on your Nilfisk-ALTO Pressure Washer, top up the fuel. Cold water operation is possible.
General| Number of Pistons | 3 |
|---|---|
| Ceramic Pistons | Yes |
| Pump Pressure (bar/MPa) | 120 bar |
| Power Consumption (kW) | 1.5 kW |
| Weight (kg) | 27 kg |
| Voltage/Phase/Frequency (V/~/Hz) | 230V/1~/50Hz |
| Cord Length (m) | 5 m |
| Max Pressure | 120 bar |
| Water Flow | 500 l/h |
| Motor Power | 1.5 kW |
| Dimensions | 400x300x400 mm |
| Weight | 27 kg |
To Next Page
