924
HOW TO USE PROGRAMS DIRECTLY FROM
OUR INTERNET SITE
Our new internet site at www.iFIT.com allows you to
access a selection of programs that interactively con-
trol your treadmill to help you achieve your specific ex-
ercise goals. In addition, you can play iFIT.com audio
and video programs directly from the internet.
To use programs from our internet site, the treadmill
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 21. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our internet site.
Follow the steps below to use a program from our
internet site.
Insert the key fully into the console.
See GETTING STARTED on page 11.
Select the iFIT.com mode.
When the key is inserted,
the manual mode will be se-
lected and the M indicator
will light. To use a program
from our internet site, press
the iFIT.com button or press
the Select Program button repeatedly until the indi-
cator on the iFIT.com button lights.
Go to your computer and start an internet
connection.
Start your web browser, if necessary, and go to
our internet site at www.iFIT.com.
Follow the desired links on our internet site to
select a program.
Read and follow the on-line instructions for using a
program.
Follow the on-line instructions to start the
program.
When you start the program, an on-screen count-
down will begin.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the key onto the waistband of your clothing.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
To stop the walking belt at any time, press the
Stop button on the console. The Time display will
begin to flash. To restart the program, press the
Start Program button or the Speed
▲▲
button. After
a moment, the walking belt will begin to move at 1
mph. When the next “chirp” is heard, the speed
and incline will change to the next settings of
the program.
When the program is completed, the walking belt
will stop and the Time display will begin to flash.
Note: To use another program, press the Stop
button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time display is not flashing. In addition,
make sure that the audio cable is properly con-
nected, that it is fully plugged in, and that it is
not wrapped around a power cord.
Follow your progress with the LED track and
the displays.
See step 5 on page 12.
When the program has ended, remove the key.
See step 6 on page 14.
9
8
7
6
5
4
3
2
1
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBE
TM
WALKING BELT
Your treadmill features a walking belt coated with PERFORMANT LUBE
TM
, a high-performance lubricant. IMPOR-
TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such
substances will deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric
current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-earthing conductor and an earth-
ing plug.
Two power cords are included. Select the one that will fit your
outlet. Refer to drawing 1. Plug the indicated end of the power
cord into the socket on the treadmill. Refer to drawing 2. Plug
the power cord into an appropriate outlet that is properly in-
stalled and earthed in accordance with all local codes and or-
dinances. Note: In Italy, an adaptor (not included) must be
used between the power cord and the outlet. Important: The
treadmill is not compatible with GFCI-equipped outlets.
Use only a power cord type H05VV-F with a conductor of at least
1mm
2
(14 gauge), with a country recognised plug and an appliance
coupler.
DANGER:Improper connection of the
equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the product is properly earthed. Do not mod-
ify the plug provided with the product—if it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
1
2
Socket on treadmill
Outlet
• The CR2032 battery may need to be replaced.
Follow the steps below to replace the battery.
Locate the battery
cover on the back of
the sensor unit. Insert a
coin into the slot in the
cover and turn the
cover counterclockwise
to the “open” position.
Remove the cover.
Next, remove the old
battery from the sensor
unit. Insert a new CR
2032 battery, making
sure that the writing is
on top. In addition, make
sure that the rubber gas-
ket is in place in the
sensor unit. Replace the
battery cover and turn it
to the closed position.
CR2032
Battery
Rubber
Gasket
Battery Cover
To Next Page
Loading...
Need help?
General
