Oce im4512 - User Manual

Other manuals for Oce im4512

Settings Guide28 pages

Facsimile Operation Manual116 pages

Questions and Answers

J
james33Sep 15, 2025
What to do if the scanned image is clipped when using my Oce im4512?
- J
  jenny29Sep 15, 2025
  If the scanned image is clipped, it means that the set original scanning size is smaller than the actual original size. To fix this, set the actual original size. If you intentionally set a smaller size than the actual original size, place the original taking into account the guides for the set original size. For example, when scanning an 8-1/2" x 11" (A4) original using a 5-1/2" x 8-1/2" (B5) setting, align the original using the scale at the left edge to fit the area you wish to scan into the 5-1/2" x 8-1/2" (B5) scanning area.
M
Matthew GreeneSep 23, 2025
What to do if the scanned image range is on the opposite side of the selected image range on my Oce im4512 All in One Printer?
- C
  Christine ReillySep 23, 2025
  If the scanned image range is on the opposite side of the selected image range, it means that the original was placed with the left and right sides reversed. Place the original in the correct orientation.
P
Patricia MiddletonSep 6, 2025
Why is two-sided printing not possible on my Oce All in One Printer?
- D
  Denise SmithSep 6, 2025
  If two-sided printing is not working on your Oce All in One Printer, ensure that two-sided printing is enabled in the printer driver. Also, two-sided printing might be disabled in the administrator settings.
R
ryan90Aug 27, 2025
Why can't I select my Oce im4512 from my computer?
- R
  robertwilliamsAug 27, 2025
  If your Oce All in One Printer isn't being selected by your computer, ensure that the appropriate printer driver has been installed correctly. If not, install the driver.
R
Ricardo McculloughAug 27, 2025
What to do if my Oce im4512 receives data but does not print?
- T
  Thomas AlexanderAug 27, 2025
  If your Oce All in One Printer receives data but doesn't print, it might be due to the loaded paper not matching the specified size and type. Load the correct paper, select a different paper size, or cancel the printing job.
S
Samantha HendricksAug 28, 2025
How to fix Oce im4512 All in One Printer that prints in reverse order?
- E
  Ernest LyonsAug 29, 2025
  If your Oce All in One Printer prints in reverse order, the reverse page order setting might be enabled in your software application. Disable this setting in the application software to print in the correct order.
K
Karen WilsonAug 30, 2025
Why is the printed image cut off by my Oce im4512?
- K
  Kathryn KennedyAug 30, 2025
  If the printed image from your Oce All in One Printer is cut off, it is possible that an incorrect ratio has been selected. To resolve this, select a suitable ratio when printing.
J
Jordan CarrollSep 18, 2025
Why is the scanned image upside down or on its side with my Oce All in One Printer?
- J
  johnwoodardSep 18, 2025
  If the scanned image appears upside down or on its side, it's likely because the original was not placed in the correct orientation. Make sure to place the original in the correct orientation.
S
sarah60Sep 16, 2025
How to fix a moiré (stripe pattern) on a scanned image with my Oce im4512?
- B
  brent00Sep 16, 2025
  A slight amount of moiré can sometimes appear when scanning printed material. If you are using the document glass, try slightly shifting the position or angle of the original on the glass.
B
Brandon FowlerSep 7, 2025
Why is not all of the image is printed by my Oce All in One Printer?
- C
  Claire RobertsSep 8, 2025
  If not all of the image is printed by your Oce All in One Printer, it may be due to multiple applications running simultaneously. Close any unused applications and attempt to print again.