What to do if paper jams in the Oce Printer?
To resolve paper jams in the Oce printer, follow these steps: * Turn off the printer. * Open the correct roll compartment. * Lower the feed table using the two catches on the front underneath the feed table. * Remove the jammed material. * Close the feed table. * Close the roll compartment. * Turn on the printer. * Open the fusing section.
How to fix original jams in Oce Printer scanner?
To address original jams in the scanner of your Oce printer: 1. Stop the original with the orange Cancel key. 2. Unlock the top cover by pushing the front side down and pulling it towards you. 3. Raise the cover. 4. Remove the original. 5. Lower the top cover. 6. Lock the cover by pushing the front side down and pushing it back until you hear a click. 7. Press the Cancel key.
What to do if there are no reinforcement strips on the output of the Oce printer?
If there are no reinforcement strips on the output of your Oce printer without an error message, here’s what you can do: * Put the printer off-line by pressing the On-line key on the operator panel. * Open the side door of the reinforcement unit. * Check for loose reinforcement strips in the unit with the protection sheet still on. * Remove the tape strips in the reinforcement unit. * Remove all tape between the rollers and knives. * Lead a new trailing strip of tape between the rollers and knives.
How to clear tape jam in Oce Printer reinforcement unit?
To clear a tape jam in the reinforcement unit of your Oce printer: 1. Open the front door of the reinforcement unit. 2. Turn the two guide plates away from the pin roller and lock them into their open position. 3. Remove all tape between the rollers and knives. 4. Lead a new trailing strip of tape between the rollers and knives.
What to do if the Oce Printer has paper jams in the folder?
To resolve paper jams in the folder of your Oce printer, follow these steps: 1. Open the top cover of the folder. 2. Remove any jammed printing material. 3. Open the cover of the first fold section. 4. Open the guide plate. 5. Remove any jammed printing material. 6. Close the guide plate. 7. Close the cover of the first fold section. 8. Close the top cover of the folder.
How to clear paper jam in the Oce Printer reinforcement unit?
To clear a paper jam in the reinforcement unit of your Oce printer: 1. Open the cover of the transport to the First Fold delivery and remove all paper inside. 2. Close the cover of the folder transport section. 3. Open the front door of the reinforcement unit. 4. Open the top cover of the reinforcement unit and remove all paper inside. 5. Close top cover and side door of the reinforcement unit.
Describes the Océ TDS400 as a wide format, black and white, multifunctional system.
Details the controller's role in processing print/copy jobs, set processing, spool memory, and network connectivity.
Provides step-by-step instructions for powering the printer system on and off.
Covers media type and size settings, manual feed, and cutting media for printing operations.
Covers language selection, network setup, paper series, memory clearing, and diagnostic mode.
Outlines fundamental copy operations like turning scanner on/off, making copies, and selecting media.
Provides instructions on how to turn the scanner on/off and start or stop a copy job.
Covers setting the number of copies, selecting media rolls or manual feed, and input modes.
Explains how to adjust zoom factors and exposure settings to improve copy quality.
Explains Océ Scan Logic for scanning documents to network directories with image enhancement.
Provides step-by-step instructions for scanning an original to a file using the scanner panel.
Details scan settings like destination, checkprint, resolution, file format, and optimization.
Covers creating, deleting, locking, and defining local, network (SMB), and FTP destinations.
Explains the purpose of the Settings Editor for configuring system defaults by Key Operators and System Administrators.
Guides Key Operators on how to set default printer and copy job parameters via the Settings Editor.
Instructs System Administrators on configuring printer language, pen settings, and system parameters.
Describes the System Control Panel (SCP) application for viewing system status information.
Explains the Queue Manager application for graphical representation and management of print jobs.
Covers viewing, deleting, holding, restarting, and moving print jobs within the queue.
Introduces Océ Remote Logic for viewing system status, managing print jobs, and changing settings remotely.
Provides installation procedures for Océ Remote Logic on MS Windows and Unix systems.
Step-by-step guide for loading paper into roll 1 and roll 2 of the printer.
Instructions for refilling toner and replacing the waste toner bag when prompted.
Provides instructions on how to remove jammed originals from the scanner.
Details how to clear paper jams in the material feed section and the fuser section of the printer.
Explains how to clear paper jams in the first fold, transport, second fold, and belt sections of the folder.
Addresses paper jams, tape jams, and missing reinforcement strips in the reinforcement unit.
Provides essential safety rules for maintenance, connection, and general operation of Océ equipment.
General| Print Speed (Color) | 40 ppm |
|---|---|
| Media Size | A4 |
| Connectivity | Parallel, Ethernet |
| Operating System Compatibility | Windows |
| Toner | Black |
| Media weight | 60 - 110 g/m² |
| Interfaces | Parallel, Ethernet |
| Scan Resolution | 600 x 600 dpi |
| Display | LCD |
To Next Page
