Oki MC332dn Startup Guide

- 13 -
Installing Your Machine
1
Machine Setup
●● Installing Your Machine
This section explains how to unpack and install the machine.
Installation Requirements
This section explains the required environment
and space for machine installation.
Installation Environment
Your machine must be installed in the following
environment:
Temperature: 10°C~32°C
Humidity: 20%~80% RH (relative
humidity)
Maximum wet bulb
temperature: 25°C
Note
● Be careful of condensation. It may cause a malfunction.
● If installing your machine where the relative humidity of
the surrounding air is less than 30%, use a humidier or
antistatic mat.
WARNING
● Do not place in hot locations or near re.
● Do not install in locations where chemical
reactions take place (laboratory etc.).
● Do not place in locations near ammable solutions
such as alcohol and thinner.
● Do not place in locations within reach of small
children.
● Do not install in unstable locations (wobbly stand,
angled place, etc.).
● Do not install in locations with high humidity or
dust and where exposed to direct sunlight.
● Do not install in an environment exposed to briny
air and corrosive gas.
● Do not install in locationss with much vibration.
● Do not install in locations where the ventilation
holes of the machine are blocked.
CAUTION
● Do not place directly on a rug or carpet with long
strands.
● Do not install in a closed room with poor
ventilation or circulation.
● If you use the machine in a small room for a long
time, please make sure that you ventilate the
room.
● Install away from strong magnetic elds and
sources of noise.
● Install away from monitors or TVs.
● When moving the machine, hold it on both sides,
and move it by slightly tilting the back down.
Installation Space
Install your machine on a at surface that is
wide enough to accommodate the machine.
Allow for enough room around your machine
according to the images below.
● Top view
100cm
20cm
20cm
60cm
● Side view
60cm

Oki MC332dn Specifications

General

Duplex printing	Yes
Print technology	Laser
Maximum resolution	- DPI
Print speed (black, normal quality, A4/US Letter)	22 ppm
Print speed (color, normal quality, A4/US Letter)	20 ppm
All-in-one functions	Copy, Print, Scan
Color all-in-one functions	Scan
Digital sender	No
Maximum duty cycle	30000 pages per month
Page description languages	PCL 5c, PCL 6, PostScript 3, SIDM
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	99 copies
Time to first copy (black, normal)	12 s
Time to first copy (color, normal)	14 s
Copy speed (black, normal quality, A4)	20 cpm
Copy speed (color, normal quality, A4)	22 cpm
Scan to	CIFS, E-mail, USB
Input color depth	48 bit
Output color depth	24 bit
Scan speed (black)	30 ppm
Optical scanning resolution	1200 x 1200 DPI
Total input capacity	250 sheets
Maximum input capacity	350 sheets
Multi-Purpose tray input capacity	100 sheets
Auto document feeder (ADF) input capacity	50 sheets
Envelopes sizes	9, DL
Maximum print size	216 x 297 mm
Duplex media weight	60 - 90 g/m²
Paper tray media types	Envelopes
Paper tray media weight	64 - 176 g/m²
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5
ISO C-series sizes (C0...C9)	C5
Maximum ISO A-series paper size	A4
Multi-Purpose Tray media weight	64 - 220 g/m²
Auto Document Feeder (ADF) media weight	60 - 105 g/m²
Display	LCD
Product color	White
Display resolution	320 x 128 pixels
Market positioning	Business
Standard interfaces	Ethernet, USB 2.0
USB 2.0 ports quantity	2
Internal memory	256 MB
Sound power level (standby)	52 dB
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (average operating)	500 W
Operating temperature (T-T)	10 - 32 °C
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	509 mm
Width	427 mm
Height	444 mm