OMAC B430 - Materials, Seals and Options Codes

MATERIALS, SEALS AND OPTIONS CODES
41
MATERIALS
A-304 AISI STAINLESS STEEL B-316 AISI STAINLESS STEEL C-420 AISI STAINLESS STEEL D-DUPLEX STAINLESS STEEL DS - SAF 2507 DUPLEX S.S. E-DEW88MET ALLOY F-IRON G-G 25 CAST IRON H-HASTELLOY-ALLOY C 276 I - MONEL J-TITANIUM DEGREE 2 K-CUPRONICKEL KA - KALREZ
®
L-ALUMINIUM M-CARBON STEEL N-BRASS &-ACTEON P-TEFLON (PTFE) Q-S1 POLYMER R-MECTON S POLYMER S-SILICON RUBBER T-NBR U-EPDM V-VITON W-HYPALON Y-NATURAL RUBBER Z-ELECTRICAL MATERIAL
TYPE OF SEALS
0-LIP SEAL VITON UM
LIP SEAL EPDM UM LIP SEAL POLYMER S1
1-TEFLON PACKING GLAND 2-TEFLON FLUSHED PACKING GLAND 3-MECHANICAL SEAL: BTC5E - B2GVGG (316 S.S./CARBON/VITON)
MECHANICAL SEAL: BTC5E - B2GEGG (316 S.S./CARBON/EPDM) MECH. SEAL: UNITEN 7K - X7XZ7HX (316 S.S./CARBON/EPDM) MECH. SEAL: FLUITEN KL2A Z32Y1DJE (316 S.S./CARBON/EPDM)
4-MECH. SEAL: UNITEN 7K - X73Z7HX (TUNG. CARBIDE/CARBON/EPDM)
MECH. SEAL: UNITEN 7K - XY3ZYHX (TUNG. CARBIDE/CARBON/VITON)
MECH. SEAL:
FLUITEN KL2A Z32K22DJE (TUNG. CARBIDE/CARBON/EPDM)
5-
MECH. SEAL: UNITEN 7K - X7337HX (TUNG. CARBIDE/TUNG. CARBIDE/EPDM) MECH. SEAL: UNITEN 7K - XY33YHX (TUNG. CARBIDE/TUNG. CARBIDE/VITON) MECH. SEAL: FLUITEN KL2A K22K22DJE (TUNG. CARBIDE/TUNG. CARBIDE/EPDM)
6-MECH. SEAL: BTC5E - B2V1VGG (CERAMIC/CARBON/VITON)
MECH. SEAL: FLUITEN KL2A Z32 CDJE (CERAMIC/CARBON/EPDM)
7-MECH. SEAL: BTC5E - YV1VGG (CERAMIC/RULON/VITON) 8-
MECH. SEAL: FLUITEN KL2A U32U31VJE (SILICON CARBIDE/SIL. CARB./EPDM)
Q- DOUBLE MECHANICAL SEAL: FLUITEN KL2A (REQUIRED MATERIALS) MATERIALS FOR SEALS (TYPES)
- METALS, CARBIDES, OXIDES H - 304 STAINLESS STEEL (UNITEN) X - 316 STAINLESS STEEL (UNITEN) G - 316 STAINLESS STEEL (BT) J - STELLITE (UNITEN) L - HASTELLOY (UNITEN) 3 -
BRAZED TUNG. CARBIDE (WIDIA) (UNITEN)
R -
INTEGRAL TUNG. CARBIDE (WIDIA) (UNITEN)
K - SILICON CARBIDE (UNITEN) 2 - CERAMIC (UNITEN) V1 - CERAMIC (BT)
- CARBONS, RESINS, ELASTOMERS Z - CARBON (UNITEN) B2 - CARBON (BT) 5 - TEFLON (UNITEN) 4 - RULON (UNITEN) Y - RULON (BT) F - O-RING FEP (UNITEN) E - EPDM (BT) 7 - EPDM (UNITEN) Y - VITON (UNITEN) V - VITON (BT)
SPECIAL VERSIONS
A-ASEPTIC PUMP B C-FLUSHED MECHANICAL SEAL D-DUPLEX SHAFTS E-
STAINLESS ANTI-SEIZURE ALLOY ROTORS
F-POLYMER/HASTELLOY PUMP G-INNER POLISHING SURFACE H-HIGH PRESSURE PUMP I-MONEL 400 PUMP J - TITANIUM PUMP K-SURFACE HARDENING L-ENLARGED INLET PORT M-POLYMER/MONEL PUMP N O P-TEFLON TRIM Q-DOUBLE FLUSHED MECH. SEAL R-ROTOR CASE WITH HEATING JACKET S-S1 POLYMER LIP SEAL T-HYDRAULIC FLANGE PUMP U - EPDM TRIM V-VITON TRIM W - POLYMER/TITANIUM PUMP Y - HASTELLOY PUMP Z - HASTELLOY/TITANIUM PUMP 1-END COVER WITH RELIEF VALVE 2-END COVER WITH HEATING JACKET