To Next Page
T
Tom SmithAug 17, 2025
Why is my Omron Touch terminal not supplying power normally?
- RrloganAug 17, 2025
If your Omron Touch terminal isn't receiving power, check the power supply voltage and ensure it matches the recommended voltage.
Why is my Omron Touch terminal not supplying power normally?
If your Omron Touch terminal isn't receiving power, check the power supply voltage and ensure it matches the recommended voltage.
What to do if cables are not connected correctly to Omron NS10-TV Touch terminals?
If the cables aren't connected properly to your Omron Touch terminals, verify all cable connections and reconnect them correctly.
What to do if the terminating resistance is not set correctly on Omron NS10-TV Touch terminals?
If the terminating resistance isn't set correctly on your Omron Touch terminals, turn ON the terminating resistance at the nodes at both ends of the network and turn it OFF at all other nodes.
What to do if the Controller Link Interface Unit has become loose in Omron NS10-TV Touch terminals?
If the Controller Link Interface Unit is loose in your Omron Touch terminals, ensure it is firmly secured.
What to do if the same node address is being used in the same network for Omron NS10-TV?
If the same node address is being used in the same network for your Omron Touch terminals, reset the settings so that each node address is used only once within the same network.
What to do if the Omron Touch terminal node address is larger than the maximum?
If the node address is larger than the maximum node address set for the network parameters on your Omron Touch terminal, either reset the maximum node address using Controller Link Support Software or reset the node address to below the maximum.
How to fix a faulty Controller Link Interface Unit in Omron Touch terminals?
If the ERC indicator lights even after mounting on another PT, replace the Controller Link Interface Unit. If indicators do not light when the Board is mounted on another PT, replace the Controller Link Interface Unit.
What to do if there is an EEPROM error on Omron Touch terminals?
If an EEPROM error occurs on your Omron Touch terminals, send a FINS command to the Controller Link Interface Unit to read status, correct the data where the error has occurred, and reset the Board. If the error occurs again, replace the Controller Link Interface Unit.
What to do if the set baud rate is different from other nodes on Omron NS10-TV Touch terminals?
If the set baud rate is different from other nodes on your Omron Touch terminals, reset the baud rate for the Controller Link in the CX-Designer’s Communication Setting.
What to do if there are no other nodes existing in Omron Touch terminals network?
If no other nodes exist within the Network for Omron Touch terminals, ensure that 2 or more nodes exist within the Network.
Specifies the system configuration requirements for NS-V1/V2 models to connect via Host Link.
Lists OMRON PLCs compatible for connection as hosts using Host Link communications.
Details connecting NS-V1/V2 PTs to hosts via RS-232C ports, including compatible units and settings.
Explains connecting NS-V1/V2 PTs to hosts via RS-422A/485 ports, including compatible units.
Guides on creating screen data using CX-Designer for Host Link communication setup.
Describes the procedure for transferring screen data from CX-Designer to the NS-V1/V2 PT.
Details setting the communications method and baud rate for serial ports on the NS-V1/V2 PT.
Details the PLC memory areas usable for Host Link communications in OMRON C-series PLCs.
Specifies the PLC memory areas usable for Host Link communications in CVM1/CV-series PLCs.
Specifies the required CX-Designer project versions for successful Host Link communication.
Identifies which serial ports (A or B) on NS-V1/V2 PTs are supported for Host Link.
Lists the NS-series PT models that are compatible with Host Link communications.
General| Display Type | TFT LCD |
|---|---|
| Touch Type | Resistive |
| Backlight Life | 50, 000 hours |
| USB Port | USB 2.0 |
| Ethernet | 10/100 Mbps |
| Serial Port | RS-232C |
| Operating Temperature | 0°C to 50°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 10% to 90% (non-condensing) |
| Shock Resistance | 147 m/s², 3 times each direction |
| Power Supply | 24 VDC |
| Protection Rating | IP65 (front panel) |
| Vibration Resistance | 10 to 57 Hz: Amplitude 0.075 mm, 57 to 150 Hz: 9.8 m/s2 |
