EasyManua.ls Logo

Omron Q2A Series - User Manual

Omron Q2A Series
26 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1Q2A
Q2A
Driving Quality
• Advanced motor control for IM, PM & SynRM motors
• Open/closed loop speed or torque control
• Embedded functional safety (STO SIL3)
• Built-in C3 class EMC filter
• Conform to EN 60721-3-3, 3S2 and 3C2
• Built-in braking transistor (models up to 90 kW)
• Quick and easy setup with intuitive keypad and navigation
• Micro SD for data storage
• Real-Time Clock
• 24 VDC power supply input for control board
• Communication options: EtherCAT, EtherNet/IP,
PROFINET, Modbus TCP/IP, POWERLINK
• Up to 5 Q2A with a single communication option card
• PC configuration tools: Q2edit and Q2dev
• Mobile Device connectivity (via USB or optional Bluetooth)
• Regenerative solutions as option
• CE, UL, cUL, EAC, RoHS
Ratings
• 400 V class: 0.55 to 315 kW
System configuration
LCD Remote
Installation
Remote Operator
Extansion Cable
Mounting
Bracket
MCCB
Q2A
Filter
Input AC
Reactor
Motor
Ground
Power
Supply
Braking Resistor
DC Reactor
Feedback Speed Option Card
Input/Output Option Card
Choke
Output AC Reactor
orBraking chopper
R1000 kit
*2
Regenerative solution
D1000 kit
*1
Regenerative solution
The D1000 kit includes a Regenerative DC bus supply
unit (D1000), EMC filter and low harmonic filter. If the
D1000 kit is purchased, it is not necessary to buy the
EMC filter as separate item.
The R1000 kit includes a Regenerative braking unit
(R1000) and current suppression reactor.
*1.
*2.
USB Cable
Communication Option Card
I175E-EN-01+Q2A+Datasheet.fm Seite 1 Montag, 26. März 2018 3:18 15

Table of Contents

Other manuals for Omron Q2A Series

Preview: Technical Manual
Technical Manual844 pages

Questions and Answers

  • J
    Jonathan MartinAug 4, 2025
    Why won't the Omron Controller motor rotate after entering the run command?
    • K
      Kristina WatsonAug 4, 2025
      The motor may not rotate after entering the run command for several reasons. The drive might not be in Drive Mode, indicated by the keypad not showing [Rdy]. Ensure the keypad displays [Rdy] or return to the Home screen. A fast stop command could have been received; if so, turn off the fast stop input signal. The settings for the Run command source (b1-02) or the frequency reference source (b1-01) might be incorrect, so verify these settings. Defective wiring in the control circuit terminals or incorrect voltage/current input settings for the master frequency reference could also be the cause. Also, check if the frequency reference is too low, and if so, increase it above the minimum output frequency (E1-09). Finally, confirm the sinking/sourcing mode and power supply settings are correct.
  • D
    Douglas WrightAug 11, 2025
    What to do if the Omron Controller motor is too hot?
    • R
      Ronnie WilliamsAug 11, 2025
      If the Omron Controller motor is overheating, it could be due to a heavy load or continuous operation at very low speed. Reduce the load, increase acceleration and deceleration times, and examine the values set in L1-01, L1-02, and E2-01. Consider using a larger motor. If the motor is running continuously at a very low speed, change the run speed or use a drive-dedicated motor.
  • B
    Barry SmithAug 18, 2025
    Why is the Omron Q2A drive frequency reference different from the controller frequency?
    • A
      Allison WilsonAug 19, 2025
      The discrepancy between the drive frequency reference and the controller frequency in your Omron system can stem from several factors. The analog input gain and bias for the frequency reference input might be incorrectly configured; examine the settings for Terminals AI1, AI2, and AI3. The drive could be receiving frequency bias signals from analog input terminals AI1 to AI3, with the sum affecting the frequency reference; check parameters H3-02, H3-10, and H3-06. If PID control is enabled and not required, disable it by setting b5-01 = 0.
  • T
    Tyler ThomasNov 26, 2025
    How to fix Omron Q2A Controller motor stalls during acceleration?
    • R
      Ronald CarterNov 26, 2025
      If the Omron Controller motor stalls during acceleration, it could be due to several reasons. The drive and motor system may have reached the torque limit. Decrease the load or use a larger motor. The torque limit setting could be incorrect, so ensure it is properly configured. If the acceleration time is too short, check the values set in C1-01, C1-03, C1-05, or C1-07 and adjust them accordingly. Also, a low frequency reference can cause this issue. Examine E1-04 and U1-01, and check the multi-function input terminals and low gain levels in H3-03, H3-11, and H3-07. If the motor characteristics and drive parameter settings are incompatible, set the correct V/f pattern and perform Rotational Auto-Tuning. If operating in vector control mode, complete Auto-Tuning or switch to V/f Control by s...

Summary

Q2 A Inverter Key Features

Driving Quality Highlights

Advanced motor control, embedded safety, built-in EMC filter, and quick setup features.

Q2 A Inverter Detailed Specifications

400 V Class Output Characteristics

Table detailing inverter capacity, rated output current, and voltage for 400V class models.

Power Supply and Overload Details

Common Specifications and Control Functions

Includes control methods, frequency ranges, torque control, speed control, and setting resolution.

Inverter Functionality, Protection, and Safety

Main Control and Functionality Features

Details V/f characteristics, motor control modes, and operational features like zero servo.

Protection Functions and Overload Handling

Describes protections such as overcurrent, overload, overvoltage, and momentary power loss.

Environmental, Safety, and Protection Design

Covers ambient conditions, safety standards (UL, EN), and enclosure protection ratings.

System Kits for Enhanced Functionality

D1000 Kit - Regenerative DC Bus Supply

R1000 Kit - Regenerative Braking Unit

Braking and Suppression Components

Braking Units and Resistor Options

Specifications for braking units (CDBR) and braking resistors (AX-REM).

Installation, Wiring, and Connections

Standard Connection Diagram

Visual guide for connecting power supply, main circuit, control circuit, and accessories.

Main and Control Circuit Terminals

Ordering Information and Model Selection

Q2 A Inverter Model Selection Guide

Table detailing Q2A inverter models based on motor capacity, rated current, and duty.

Omron Q2A Series Specifications

General IconGeneral
BrandOmron
ModelQ2A Series
CategoryController
LanguageEnglish

Related product manuals