Onkyo A-933

17
Enjoying Audio Sources
If the A-933 is connected to other components via
, press the remote controller’s [ON] button once
to turn on the A-933, and press it again to turn on the
other components.
Turning on all system components simultaneously:
You can set the A-933 so that all connected compo-
nents are turned on with just one press of the remote con-
troller’s [ON] button or the A-933’s [STANDBY/ON]
button. To do this, turn on the A-933, and then press and
hold the remote controller’s [ON] button for 16 seconds
until the A-933 switches to Standby mode. You will then
be able to turn on the A-933 and all system components
with just one press of the remote controller’s [ON] but-
ton or the [STANDBY/ON] button on any system com-
ponent.
Notes:
• The A-933 is shipped with the POWER switch in the
ON position ( ). When the power cord is connected
for the very first time, the A-933 will go on Standby,
and the STANDBY indicator will light up.
•To completely shut down the A-933, set the POWER
switch to the OFF position ( ).
Selecting Speaker Set A or B
You can select which set of speakers outputs sound, or
you can use both sets at the same time.
To output sound from the speakers connected to the
SPEAKERS A terminals, press the SPEAKERS [A]
button. The indicator above that button will light up. If a
subwoofer is connected, that too will output sound.
To output sound from the speakers connected to the
SPEAKERS B terminals, press the SPEAKERS [B]
button. The indicator above that button will light up. If a
subwoofer is connected, that too will output sound.
To output sound from all connected speakers, press the
SPEAKERS [A] and SPEAKERS [B] button so that
both indicators are on.
Turning On the A-933
1
Press the [POWER] button.
The STANDBY indicator lights up.
2
Press the [STANDBY/ON] button.
Alternatively, press the remote control-
ler’s [ON] button.
The A-933 turns on and the
STANDBY indicator lights up green.
Note:
When it’s turned on, the A-933 outputs
no sound for about five seconds. This
allows the circuits to stabilize.
To turn off the A-933, press the
[STANDBY/ON] button. The A-933
will enter Standby mode.
TUNER
PHONO
C D
M D
TAPE /CDR
LINE
STANDBY/ON
POWER
PHONES
TO N E
(
R
)
DIRECT
(
G
)
MAIN IN
SUPER BASS BASS
MAX
TREBLE
SPEAKERS
BA
OFF
ON
TAPE
/
CDR
CD
MD
ON
STANDBY
FM AM CLEAR
78
9
10/0
>
10
4
56
231
GROUP
STANDBY(R)
ON(G)
POWER
STANDBY/ON
ON
STANDBY
STANDBY indicator
POWER
OFFON
STANDBY/ON
ON
Remote
controller
Listening to Components
1
Turn the input selector to select
the component that you want to
listen to.
TAPE/CDR : Select to hear the compo-
nent connected to the TAPE/CDR IN
jacks.
MD : Select to listen to the component
connected to the MD IN jacks.
LINE: Select to listen to the compo-
nent connected to the LINE jacks.
CD: Select to listen to the component
connected to the CD jacks.
TUNER: Select to listen to the compo-
nent connected to the TUNER jacks.
PHONO: Select to listen to the turnta-
ble connected to the PHONO jacks.
TAPE
/
CDR
PRESET
VOLUME
VOLUME
CD
MD
PRESET
SLEEP
ON
STANDBY
FM AM CLEAR
78
9
10/0
>
10
4
56
231
GROUP
TIMER
ENTER
MUTING
TUNER
PHONO
C D
M D
TAPE /CDR
LINE
STANDBY/ON
STANDBY(R)
ON(G)
POWER
PHONES
TO N E
(
R
)
DIRECT
(
G
)
MAIN IN
SUPER BASS BASS
MAX
TREBLE
SPEAKERS
BA
OFF
ON
MUTING
SPEAKERS A, B
VOLUME
/
Input selector
Volume
TUNER
PHONO
C D
M D
TAPE /CDR
LINE
*EnA93302.fm Page 17 Tuesday, January 25, 2005 1:46 PM