Connections
AC OUTLETS
'Ihe TX-SR701/701E/601/6OIE is equipped with AC mains outlets
for connecting the power coMs from other devices so that their
power is supplied through the TX-SR701/701 E/601/601E. By doing
this, you can leave the connecled device turned on and have the
STANDBY/ON button on the TX-SR701/701E/601/601E turn on
and off the device together with the TX-SR701/701 E/601/601E.
Tile shape, number, and total capacity of the AC outlets may
differ depending on the area of purchase.
Caution:
Make sme that the total capacity of the components connecled to
the TX-SRT01/701E/601/601E does not exceed the capacity that is
printed on the rear panel (e.g., TOTAL 120W).
European and USA and Canadian
some Asian models models
RI REMOTE CONTROL
'Ihe Ill terminal on the TX-SR701/701E/601/601E is for
connecting other Onkyo components equipped with the R I same
terminal. When a component is connecled to the terminal, it can be
operated by the remole controller supplied with the TX-SR701/
701E/601/601E. In addition, when you connect a component to the
1"211terminal, you can also perform the system opera/ions given
below.
Power on/ready function
When the TX-SR701/701E/601/601E is in the standby state, if an
Ill-connected component is turned on, the TX-SRT01/701E/601/
601E also turns on and the input source selecled a/the TX-SR701/
701E/601/601E aulomatically swilches to thai component.
Be aware that this function will not work if the power coM for the -
connected component is connecled to the AC OUTLFF on the TX-
SRT01/701E/601/601E, or if the TX-SRT01/701E/601/601E has
already been turned on.
Direct change function
When the play button is pressed a/ an Ill-connected component,
the input source selecled at the TX-SR701/701E/601/601E
automatically changes to that component.
Power off function
When the TX-SR701/701 E/601/601E is placed in the standby state,
all Ill-connected components are also automa/ically put into the
standby stale.
Also, if you press the ON button on the TX-SR701/701E/601/601E
remote controller while the TX-SR701/701 E/601/601E is turned on,
all gl-connecled components (DVD players, CD players, MD
recorders, tuners, etc.) are also mined on.
Dimmer function
The Dimmer function (display brightness adjustment) of the TX-
SRT01/701E/601/601E can be used to synchronize the display
brightness on the connected device using the I:t I connection.
Caution:
If an MD recorder is connected to the TAPE,jack on the TX-SR701/
701E/601/601E, switch the Input Selector from TAPE to MD (see
page 43).
_-..........- ==c:Ii_
R I connector
TX-SR701/701 E/601/601 E
Ex: Onkyo CD player /_::] _4:::::IIm_-.......---
/q::/
RI connector \
dEX:cOnkyocassette tape\_-]-_:4ZSItiii:--------
To connect components using the Ill /erminal, simply connect a
remote control cable from this 1"211lerminal to the Il I lerminal of
the other component. An Ill remole control cable with a I/8-inch
(3.5-mm) minia/ure two-conductor plug comes with every cassette
tape deck, compact disc player, MD recorder, and DVD player that
has an Il I lerminal.
• When performing operations with Ill-connected components
using the Il I system, do not use the remote zone (Zone 2).
• For remote control operation, the audio connection cables must
a]so be connected.
• If a component has two Il I lerminals, you can use either one to
connect to the TX-SRT01/701E/601/601E. The other one can be
used to daisy chain with another component.
• With Onkyo DVD players, you can enter the pre-program code
so thai you can operate the DVD player directly with the remote
controller without connecting the Ill terminals (see page 67).
24
To Next Page
Loading...
