HardwareSetup
Hardware Config
To display the Hardware Config menu:
1. Display the main menu.
2. Use the • and • cursor buttons to select "1. Hardware
Config" and then press the ENTER button. The "Hardware
Config" menu appears.
TX-SR701G01E TX-SR601/601 E
1.Hardware Config
***********************
I a.Surr/Zone 2:Surr
b.Surr Back : ich
c. ZR iN Posizlon
:Main
d. TV Format :Auto
e.AM Frequency Step
:9kHz_
_ @uit:ISE'PUP I
Menu *****************
l.Hardware Config
***********************
a.Surr/Zone 2 :Surf
b.iR iN Posizlon
:Main
c.TV Formaz :Auto
[_ Quit:ISETUP I
I SuP.."Zone2: SuPP I -_uPiZor)e2: SuPp
d. TV Format (TX-SR701/701E)
c. TV Format (TX-SR601/601E)
(For all models other than USA and Canadian models)
'Ihe default setting is "Auto," which means thai the television
format is detected and aulomatically set by the TX-SR701/701E/
601/601E. However, if you know the correct format, you can use
this setting to choose either PAL or NTSC so that no time is wasted
on detection.
e. AM Frequency Step (TX-SR701/701E)
d. AM Frequency Step (TX-SR601/601E)
'Ibis selling only appears on the worldwide model. It determines the
increment amount or decrement amount when ac[justing the AM
tuner frequency. The initial setting is 9 kHz, and this needs only to
be changed if you are using the TX-SR701/701E/601/601E in a I 0-
kHz regiom
a. Surr/Zone 2
If you connect the Zone 2 speakers to the ZONE 2 SPEAKERS
terminals or the amplifier connecled to the ZONE 2 PRE OUT (TX-
SR701/701E only) terminals, set the Surr/Zone 2 setting to "Zone
2, _
Surf: In this selling, sound will not be output from the Zone 2
speakers which is connecled to the ZONE 2 SPEAKERS
lerminals or the amplifier connecled to the ZONE 2 PRE OUT
(TX-SR701/701E only) terminals. In the main room, 6.1-
channel playback will always be available.
Zone 2: In this setting, when you are not using the Zone 2, 6.1-
channel playback will be available for the main room. Howevel.
while you use the Zone 2, 6.l-channel playback will not be
available for the main room (2ch stereo playback only).
b. Surr Back (TX-SR701/701E only)
Specify whether you use one surround back speaker or two.
lch: Selects when you connect one sin-round back speaker to
the SURROUND BACK SPEAKER terminals on the TX-
SR701/701E.
2ch (PILE OUT): Selects when you connect two surround back
speakers to the power amplifier connected to the SURR BACK
PRE OUT terminals on the TX-SR701/701E.
Note:
Be sure to use either one or two surround back speakers.
Connecting surround back speakers to both the SURROUND
BACK SPEAKER terminals on the TX-SR701/701E and the power
amplifier will not produce correct surround sound effect.
c. IR IN Position (TX-SR701/701E)
b. IR IN Position (TX-SR601/601E)
Use this setting when you have a remote control sensor connected
to the IR IN terminah The setting in this menu lells the TX-SR701/
701E/601/601E whether the remote control sensor is being used for
opera/ion of the TX-SR701/701E/601/601E in the main zone or the
remote zone (Zone 2).
Main: Select when you are using the remote control sensor for
operation with the remote controller in the main zone.
Zone 2: Select when you are using the remole control sensor
for operation with the remote controller in the remote zone
(Zone 2).
55
To Next Page
Loading...
