6. 7.ATM PROGRAMMING
ATM PROGRAMMING
Using your device in an ATM: An OptConnect unit accepts and routes
data by using 2 dierent methods which are outlined below. To maintain the
highest security standards, OptConnect highly recommends that the ATM be
programmed to use the wireless device as a ROUTER, allowing the ATM to house
and perform the security encryption of the ATM transaction. This programming
guide is merely informational, providing the terminal settings required for either
communication method. Each method of use has its benets and its potential
limitations. As an Operator of hardware that facilitates nancial transactions, you
should consider the benets and limitations of both routing options, as well as
their place in your business model.
OptConnect as a Router: This is OptConnect’s preferred and
recommended programming method and is the most secure way of routing
trac. In Router mode, the OptConnect unit simply directs trac from attached
equipment to a remote host. The attached equipment is programmed with the
required routing settings, performs the SSL/TLS encryption and decryption,
and passes transactional data through the cellular network provided by the
OptConnect unit to the remote host. In router mode, the OptConnect unit does
not participate in the interception, routing, or the encryption of data required
for SSL/TLS, and merely acts as a method by which the attached equipment
can connect to a wireless network. It is important to note that while using the
OptConnect as a router, the equipment software application must remain
up-to-date (according to industry standards) in order to facilitate the SSL/TLS
encryption.
Benets to using the OptConnect as a Router include:
• Data is not passed to the device unencrypted.
• Tighter security during transmission of data between attached equipment
and the OptConnect unit.
OptConnect as a Payment Gateway: This method of use allows the
device to participate in the interception, routing, and security encryption of data
provided by the attached equipment (ATM, Kiosk, POS, etc.). The OptConnect
receives unencrypted data from the attached equipment, determines remote
host protocols and routing rules, establishes an SSL/TLS session, encrypts and
decrypts data, converts data to original protocols, and returns the data to the
attached equipment.
Benets of using the OptConnect as a Payment Gateway include:
• SSL/TLS encryption facilitated by the OptConnect unit
• SSL/TLS encryption is remotely managed and updated as needed by
OptConnect (as per industry requirements)
• Higher level troubleshooting and fault triaging with OptConnect Customer
Care. An OptConnect Customer Care Associate has visible access to
encrypted data routing to the remote host(s) and can nd faults in routing
rules or terminal communication settings easily and quickly. Many customers
have learned to depend on our ability to quickly and eectively triage cellular
and/or terminal programming faults.
***ATM IS PERFORMING SSL/TLS ENCRYPTION***
NAUTILUS HYOSUNG ATMS
ROUTER
NAUTILUS HYOSUNG ATMS
Customer Setup >
Select Processor >
Communication >
Select TCP/IP
-1(X) Cancel to Return-
TCP/IP Type:
SSL: Enable
Version: TLS 1.2
SSL CERT: Disable*
-2(x) Cancel to Return-
Customer Setup >
*Standard 3 Options >
Status Monitoring: Enable
Comm Header: Enable
Comm ID: Refer to Page 25
CRC: Disabled
-2(X) Cancel to Return-
Cardtronics
Columbus Data
Data Stream (ASAI)
DNA (Money Tree)
EFX
Elan/Genpass
1st ISO / First Data / Core Data
ITS Systems Integrators Co Inc
Metavante / PAI / FIS
NRT/TNS
Planet Payment
Switch Commerce
Worldpay / RBS Lynk
Visa Framed
Standard
Visa Framed
Standard
Visa Framed
Visa Framed
Standard
Standard
Standard
Visa Framed
Standard
Visa Framed
Standard
PROCESSOR TCP/IP TYPE
*Please verify with processor if set up
on STD1 or STD3
*If your processor has issued, and
you have loaded a specic terminal
certicate on the ATM, then this
option should be ENABLED
To Next Page
Loading...
Need help?
General
