21
RQT7467
Recording
Timer recording
[HDD] [RAM] [DVD-R]
You can enter up to 32 programmes up to a month in advance.
Entering VIDEO Plus+ numbers is an easy way of timer recording. You
can find these numbers in TV listings in newspapers and magazines.
≥
Using VIDEO Plus+ numbers for Satellite stations or Cable TV stations
Set this unit to recognise VIDEO Plus+ numbers for Satellite stations
or Cable TV stations before you start the following operations
(➡ page 13, VIDEO Plus+ numbers for Satellite/Cable TV stations).
1 Press [VIDEO Plus+].
2 Press the numbered buttons to enter
the VIDEO Plus+ number.
Press [2] to move back to correct a digit.
3 Press [ENTER].
≥Confirm the programme and make corrections if necessary
using [3, 4, 2, 1] (➡ page 22, step 3).
≥When “-- ---” appears in the “Name” column, you cannot set
timer recording. Press [3, 4] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit’s memory.
≥
You can also press [REC MODE] to change the recording mode.
≥PDC (➡ right)
ON!)OFF (– – –)
≥
You can also press [HDD] or [DVD] to select the recording drive.
When the recording drive is “DVD” and there is not enough
remaining space, recording automatically switches to the
“HDD” (➡ right, Relief Recording).
≥RENEW (Auto Renewal Recording) [HDD] (➡ page 22)
ON!)OFF
≥Programme Name
Press [2, 1] to select “Programme Name” and press
[ENTER] (➡ page 46).
4 Press [ENTER].
The settings are stored.
Repeat steps 1–4 to programme other recordings.
5 Press [F TIMER].
“F” lights on the unit’s display to indicate timer recording
standby has been activated.
≥The message screen
appears. Only play is
possible while timer
recording is in standby (➡ page 24, 25). (You cannot play a
title recorded using a different encoding system from that of
the TV system currently selected on the unit.)
≥The unit is not off. To save power, turn the unit off by
pressing [Í DVD].
Using VIDEO Plus+ number to make
timer recordings
VOLUME
CH
DIRECT TV REC
DVD
TV
AV
123
456
78
0
9
MANUAL SKIP
CH
CANCEL
INPUT SELECT
SKIP
STOP
PAU SE
PLAY/x1.3
SLOW/SEARCH
FUNCTIONS
ENTER
DIRECT NAVIGATOR
TOP MENU
RETURN
SUB MENU
CREATE
CHAPTER
TIMER
EXT LINK
PROG/CHECK
REC MODEERASE
REC
AUDIO
TIME SLIP
STATUS
DISPLAY
F
A B C
DUBBING
HDD DVD
SD/PC
3,4,2,1
ENTER
F TIMER
PROG/CHECK
EXT LINK
REC MODE
VIDEO Plus+
HDD, DVD
¢ CANCEL
Í DVD
VIDEO Plus+
Numbered
buttons
VIDEO Plus
+
1:58 SP
DVD
30:24 SP
Remain HDD
12:53:00 15. 7. TUE
Enter
VIDEO Plus+
Number by using 0-9 keys.
TIMER
RECORDING
12:54:00 15. 7. TUE
Programme Name
ModeStopStartName Date
PDC
HDD
DVD
20:0019:0015/ 7 TUE SP
OFF HDD
1:58 SP
DVD
30:24 SP
Remain HDD
1 BBC
∫ To release the unit from recording standby
Press [F TIMER].
“F” goes out.
≥Be sure to press [F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if “F” is displayed.
∫ To cancel recording when recording has
already begun
Press [F TIMER].
≥You can also press and hold [∫] on the main unit for more than
3 seconds to stop recording.
[Note]
≥Timer recordings are activated regardless of whether the unit is
turned on/off.
≥Timer recordings begin when the set time is reached even
when playing.
≥Timer recordings do not begin while editing or transferring
(dubbing) in normal speed mode (➡ page 37).
≥“F” flashes for about 5 seconds when the unit cannot go to
timer recording standby.
≥If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the “F” flashes on the unit display. In this case,
press [F TIMER] to put the unit in the timer recording standby
mode.
≥When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the beginning of the later programmes (a few seconds when
recording with HDD or DVD-RAM and approximately 30
seconds when recording with DVD-R).
∫ PDC function (➡ page 56)
As long as a PDC signal is being broadcast by the TV station,
even if the broadcast programme time changes, the recording
time automatically changes to match the new broadcast time.
To activate the PDC function
In step 3 in the PDC column, press [3, 4] to select “ON”.
∫ Relief Recording
When the recording drive is set to “DVD” for timer recording and
if the programme will not fit onto the disc, the recording drive will
be altered to the “HDD” automatically.
≥If there is no disc in the tray or the disc cannot be recorded on
or when timer recording starts while transferring (dubbing), the
recording drive will be altered to the HDD.
≥The Direct Navigator shows which programmes were relief-
recorded (“ ” is displayed.) (➡ page 24).
≥If the time remaining on the HDD is insufficient, as much of the
programme as possible will be recorded onto the HDD.
≥Relief recording is not activated when recording the programme
with PDC and it is extended so that it no longer fits on the disc.
SP
OK
20:0019:00BBC1 15/ 7 TUE01
Mode
Disc
space
StopStartNo. Name Date
TIMER
RECORDING
12:55:00 15. 7. TUE
New Timer Programme
OFF
PDC
HDD
DVD
1:58 SP
DVD
30:24 SP
Remain HDD
Check to make sure “OK”
is displayed (➡ page 23).
Timer standby is active. Playback is possible.
7467en.book21ページ２００４年４月２３日 金曜日 午前９時５１分
To Next Page
Loading...
