12
13
Basic Operations
Basic Operations
RQT5897 RQT5897
Prepare the power supply (➡ pages 10 and 11).
1 Slide the lock release and open the
outer cover.
2 Press [PUSH OPEN] to open the
disc lid and insert a disc with the
side you want to play label up.
Close the disc lid by hand.
3 Press and hold [1, ON] to
start play.
The unit comes on automatically.
See below if a menu appears.
4 Adjust the volume.
Using menus: Basic operations
e.g.:
Press the numeric buttons to select an
item.
Or
Use the cursor jockey [3, 4, 2, 1] to
highlight an item and press [ENTER].
∫ Selecting an item numbered 10 and
over with numeric buttons
e.g. 10: [S10]>[1]>[0]
e.g. 25: [S10]>[2]>[5]
∫ Other menu operations
Operation of menus differs from disc to
disc, so read the disc’s instructions for de-
tails.
[9] : To move to the next menu
[:] : To return to the previous
menu
[TOP MENU]: To return to the first menu
[MENU] : To show menus
[RETURN] : To show menus
DVD VCD
DVD
∫ To turn the unit on
The unit can be turned on as follows.
OOn the main unitN
Slide [ON/OFF, HOLD] to
“ON/OFF” until the display
is turned on.
OOn the remote controlN
Press [Í, POWER].
The [Í] indicator on the unit flashes to indi-
cate the unit is on when the monitor’s mode
is set to “4 (Off)” (➡ page 19) or the outer
cover is closed.
∫ To turn the unit off
The unit can be turned off as follows. The
[Í] indicator lights when you are using the
AC adaptor.
OOn the main unitN
Slide [ON/OFF, HOLD] to
“ON/OFF” until the display
is turned off.
OOn the remote controlN
Press [Í, POWER].
Note
≥You cannot use the remote control to turn
the unit on when it is being powered by
the battery pack.
≥The unit automatically turns off after being
stopped for 15 minutes (5 minutes when
the battery pack is being used).
≥(Auto power-off function)
∫ To prevent accidental operation
Slide [ON/OFF, HOLD] to
“HOLD”.
In the hold mode, the unit does not respond
when you press the buttons. If you press a
button in the hold mode, “'” appears
on the unit’s display and the [Í] indicator
flashes.
To release:
Slide [ON/OFF, HOLD] to “ON/OFF”.
∫ “$” appears on the LCD
This indicates that an operation is not al-
lowed by the unit or disc at that time.
∫ When the disc ends
If you have finished using the unit, turn it off
to conserve power (➡ page 13, “To turn the
unit off”).
Note
≥The surface of the unit may become warm
if it is used for a long time, but this is nor-
mal and not an indication of malfunction.
≥The disc is still spinning while a menu is
on the LCD. Press [∫] if you have finished
viewing.
Basic play
Stopping play
During play
Press [∫].
The position you stopped play at is record-
ed by the unit when “1” is flashing on the
unit’s display.
While “1” is flashing on the unit’s display,
press [1] to start play from where you
stopped it (Resume function).
If you are playing DVDs, the following dis-
play also appears.
Pressing [1] while this is displayed acti-
vates the Chapter Preview feature.
If you do not press [1], the message dis-
appears and play starts from where you
stopped it.
Chapter Preview:
The beginning portions of each chapter up
to the current one are played. Full play re-
sumes from the point where you stopped
play. (Chapter Preview feature works only
within a title.)
∫ To cancel Resume function
Press [∫].
Note
≥The resume function does not work if the
disc’s play time is not displayed.
≥The resume position remains in memory
even if the unit is off.
≥It is cleared if you open the disc lid.
DVD VCD CD
Flashes
To Next Page
Loading...
