To Next PageTo Next Page
Why can't I send a call waiting tone on my Panasonic KX-TDE200 PBX?
If you cannot send a call waiting tone to the dialed extension on your Panasonic PBX, it could be because the other party has not set the Call Waiting feature. It is also possible that the other party has set Data Line Security.
Why did PC and fax communication fail with Panasonic KX-TDE200?
If the PC and fax machine communication failed with your Panasonic PBX, an indication tone may have interrupted communication.
How to stop background music on Panasonic KX-TDE200?
If the background music started suddenly on your Panasonic PBX, turn off the music.
What to do if I cannot remember Panasonic KX-TDE200 PBX feature numbers?
If you cannot remember the feature numbers for your Panasonic PBX, and if the feature numbers have been changed from the default values, write the new feature numbers in the table in "4.2.1 Feature Number Table". You can also ask your dealer to change the feature numbers for easier use.
How to fix a Panasonic KX-TDE200 display that is not shown well?
If the display is not shown well on your Panasonic PBX, change the Display contrast level.
Why is my Panasonic KX-TDE200 PBX SDN button not working?
If an SDN button on your extension does not work on your Panasonic PBX, a PDN button is not assigned on the extension corresponding to your SDN button. Create a PDN button on the desired extension.
Why are my Panasonic KX-TDE200 IP-PTs/SIP Extensions not working?
If IP-PTs or SIP Extensions do not operate on your Panasonic PBX, the cause might be an IP-EXT or DSP card malfunction, requiring you to replace the corresponding card. It could also be an IPCMPR card malfunction, which means you should replace the IPCMPR card (remember to turn off the PBX when replacing). Insufficient activation keys could also be the reason, so consider purchasing additional activation key cards from a certified dealer. Ensure that the IP-PT/SIP Extension is registered; if not, register it. A malfunctioning IP-PT/SIP Extension may also be the cause, so try replacing it. Lastly, a poor connection could be the issue; ensure an 8-pin twisted pair cable is used, CAT 5 cables are not longer than 100 m (328 ft), and a straight cable connects to a switching hub.
What to do if the LINK indicator on my Panasonic KX-TDE200 PBX IP-EXT/IP-GW/IPCMPR card is off?
If the LINK indicator of the IP-EXT, IP-GW, or IPCMPR does not turn on for your Panasonic PBX, it could be due to several reasons. An IP-EXT or IP-GW card malfunction might be the cause, suggesting you replace the corresponding card. Alternatively, an IPCMPR card malfunction could be the issue, so replacing the IPCMPR card (be sure to turn off the PBX when replacing) might help. Ensure a proper connection by using an 8-pin twisted pair cable, verifying that CAT 5 cables are not over 100 m (328 ft) in length, and using a straight cable for connection to a switching hub. Lastly, a network malfunction could be the problem; ensure all network devices are switched on.
Why are my Panasonic KX-TDE200 extensions (excluding IP-PT/SIP) not working?
If extensions (except IP-PT/SIP Extension) do not operate on your Panasonic PBX, it could be due to an extension card malfunction, in which case you should replace the corresponding card. A poor connection between the PBX and the extension could also be the problem; test the extension on the same port with a short cord, and repair the connection if it works. If a telephone with an A-A1 relay is connected, ensure a 2-wire cord is used and the relay switch is in the 'OUT' or 'OFF' position. If the extension itself is malfunctioning, test it on a working port and replace it if it still doesn't work. Finally, the wrong type of PSU could be the cause, so replace it with the appropriate type.
How to fix IP-PT connection issues with my Panasonic KX-TDE200?
If your IP-PT cannot connect to the Panasonic PBX, the problem might be due to an incorrect IP address, subnet mask address, PBX IP address, or default gateway address. Check each parameter and enter the correct value. Another potential cause is an improperly connected Ethernet cable, so ensure the Ethernet cable connections are correct. Finally, the DHCP server may not be active, so restart the DHCP server or disable DHCP and re-enter settings as appropriate.
General| LED indicators | Yes |
|---|---|
| SIP extensions | 128 |
| Number of extensions | 256 |
| Number of DECT cell stations | 32 |
Weight and Dimensions| Weight | 15966.5 g |
|---|---|
| Dimensions (WxDxH) | 424 x 276 x 439 mm |
