Technical Information
List of compatible signals
This projector can project the following image signals.
Mode
Display resolution
(dots) *
1
Scanning frequency
Dot clock
frequency
(MHz)
Picture
quality *
2
PnP
availability
*
3
Terminals
H (kHz) V (Hz)
NTSC/NTSC4.43/
PAL-M/PAL60
720 × 480i 15.7 59.9 — A
VIDEO/S-VIDEO
PAL/PAL-N/SECAM 720 × 576i 15.6 50 — A
525i (480i) 720 × 480i 15.7 59.9 13.5 A
COMPUTER/
YP
B
P
R
625i (576i) 720 × 576i 15.6 50 13.5 A
525p (480p) 720 × 483 31.5 59.9 27 A
625p (576p) 720 × 576 31.3 50 27 A
1 125 (1 080)/60i 1 920 × 1 080i 33.8 60 74.3 A
1 125 (1 080)/50i 1 920 × 1 080i 28.1 50 74.3 A
750 (720)/60p 1 280 × 720 45 60 74.3 A
COMPUTER/
YP
B
P
R
750 (720)/50p 1 280 × 720 37.5 50 74.3 A
VESA
640 × 400 31.5 70.1 25.2 A
COMPUTER
640 × 400 37.9 85.1 31.5 A
VGA
640 × 480 31.5 59.9 25.2 A
640 × 480 35 66.7 30.2 A
640 × 480 37.9 72.8 31.5 A
640 × 480 37.5 75 31.5 A
640 × 480 43.3 85 36 A
SVGA
800 × 600 35.2 56.3 36 A
800 × 600 37.9 60.3 40 A
800 × 600 48.1 72.2 50 A
800 × 600 46.9 75 49.5 A
800 × 600 53.7 85.1 56.3 A
MAC 832 × 624 49.7 74.6 57.3 A
XGA
1 024 × 768 39.6 50.1 51.9 AA
1 024 × 768 48.4 60 65 AA
1 024 × 768 56.5 70.1 75 AA
1 024 × 768 60 75 78.8 AA
1 024 × 768 68.7 85 94.5 AA
MXGA
1 152 × 864 64 71.2 94.2 A
1 152 × 864 67.5 74.9 108 A
1 152 × 864 76.7 85 121.5 B
MAC 1 152 × 870 68.7 75.1 100 A
MSXGA 1 280 × 960 60 60 108 A
SXGA
1 280 × 1 024 64 60 108 A
1 280 × 1 024 80 75 135 B
1 280 × 1 024 91.1 85 157.5 B
SXGA60+
1 400 × 1 050 64 60 108 A
1 400 × 1 050 65.1 59.9 122.4 B
UXGA 1 600 × 1 200 75 60 162 B
WIDE750 (720)
1 280 × 720 44.8 59.9 74.5 A
1 280 × 720 37.1 49.8 60.5 A
WXGA768
1 280 × 768 39.6 49.9 65.3 A
1 280 × 768 47.8 59.9 79.5 A
WXGA800
1 280 × 800 41.3 50 68 A
1 280 × 800 49.1 60.2 69.1 A
1 280 × 800 49.7 59.8 83.5 A
WXGA+ 1 440 × 900 55.9 59.9 106.5 A
WSXGA+ 1 680 × 1 050 65.3 60 146.3 B
WUXGA 1 920 × 1 200 74.6 59.9 193.3 B
The “i” appearing after the resolution indicates an interlaced signal.*1:
The following symbols are used to indicate picture quality.*2:
AA: Maximum picture quality can be obtained.
A : Signals are converted by the image processing circuit before picture is projected.
B : Some loss of data occurs to make projection easier.
The signals marked with circles (*3: ) can be applied by plug-and-play device.
To Next Page
Loading...
