Panasonic PT-MZ670

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 119
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON] ― Switches on the projector.
[STANDBY] ― Enters standby.
[QUICK STARTUP]
[ON]
Enables the function of the [PROJECTOR SETUP] menu → [ECO
MANAGEMENT] → [QUICK STARTUP].
[OFF]
Disables the function of the [PROJECTOR SETUP] menu → [ECO
MANAGEMENT] → [QUICK STARTUP].
[SHUTTER]
[OPEN] Disables the shutter function (shutter: open).
[CLOSE] Enables the shutter function (shutter: closed).
[INPUT]
[RGB1] Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[VIDEO] Switches the input to VIDEO.
[HDMI1] Switches the input to HDMI1.
[HDMI2] Switches the input to HDMI2.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[MEMORY VIEWER] Switches the input to MEMORY VIEWER.
[Panasonic APPLICATION] Switches the input to Panasonic APPLICATION.
[MIRRORING]
*1
Switches the input to MIRRORING.
[INPUT1] - [INPUT10]
*2
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[LIGHT POWER]
[NORMAL] Prioritizes luminance.
[ECO]
Controls the power to increase the life of the light source although
the luminance is lower than that of [NORMAL].
[QUIET]
Prioritizes the operation with less noise although the luminance is
lower than that of [NORMAL].
[IN STANDBY MODE(AUDIO)]
[OFF] Stops the audio output during standby.
[ON] Outputs the audio during standby.
[VOLUME] [0] - [63] Sets the volume.
*1 [MIRRORING] is displayed when the optional Wireless Module (Model No.: ET-WM300) is attached.
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.
11) Press the <ENTER> button.
f The command is xed and n is displayed at the left of the selected command.
f After the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 117)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[RS-232C]
Set the communication condition of the <SERIAL IN> terminal. Refer to “<SERIAL IN> terminal” (x page 213).
1) Press as to select [RS-232C].
2) Press the <ENTER> button.
f The [RS-232C] screen is displayed.
3) Press as to select [INPUT SELECT].
4) Press qw to switch the item.
[PROJECTOR] Performs the RS-232C communication with the <SERIAL IN> terminal of the projector.
[DIGITAL LINK]
Performs the RS-232C communication via the optional DIGITAL LINK output supported device (Model
No.: ET-YFB100G, ET-YFB200G) and the <DIGITAL LINK/LAN> terminal.