Panasonic PT-MZ670

Chapter 4 Settings — [NETWORK/USB] menu
146 - ENGLISH
2) Press the <ENTER> button.
f The [MEMORY VIEWER] screen is displayed.
3) Press as to select an item, and press qw to change the setting.
f The items will switch each time you press the button.
[VIEW]
Sets the display view of the Memory Viewer screen.
[THUMBNAIL] Displays the les in thumbnail view.
[LIST] Displays the les in list view.
[SORT]
Sets the display order of les in the Memory Viewer screen.
[NAME] Displays the les in the ascending order by the le name.
[TYPE] Displays the les by the types of les.
[TIME]
Displays the les in order from the le whose update time is the
oldest.
[AUTOPLAY]
Enables/disables automatic playback.
[OFF] Select this item to disable automatic playback.
[ON] Select this item to enable automatic playback.
[SCENARIO]
Select this item to perform automatic playback following the
scenario le registered from “Multi Monitoring & Control Software”.
[INTERVAL]
Sets display duration of the still image that is being automatically played back.
[5S] - [120S]
Sets the display duration of still image.
Select an item from [5S], [10S], [15S], [30S], [60S], and [120S].
[EFFECT]
Sets special effects used when changing the playback screen of still image content.
[OFF] Does not apply special effects.
[RANDOM] Applies special effects randomly.
[WIPE LEFT] Displays the image gradually from the left like wiping.
[WIPE RIGHT] Displays the image gradually from the right like wiping.
[WIPE DOWN] Displays the image gradually from the top like wiping.
[SPLIT]
Displays the image gradually from the center toward the left and
right like wiping.
[ZOOM OUT]
Displays the image gradually from the center towards the entire
image.
[FADE] Displays the entire image gradually.
[BLIND] Displays the image gradually like opening vertical blind.
[CHECKER WIPE]
Displays the image gradually from the left to right in checkerboard
patterns.
[SLIDE IN] Displays the next screen as if it slides in from the right to left.
[SLIDE OUT]
Displays the next screen by removing the current screen as if it
slides out from the right to left.
[GUIDE]
Shows/hides the operation guide on the playback screen and the time bar that visually represents the
playback progress of a movie.
[ON]
Select this item to display the operation guide and the time bar (only
for movie playback) while playing back the still image/movie.
[OFF]
Select this item not to display the operation guide and the time bar
while playing back the still image/movie.
Note
f For how to use the Memory Viewer, refer to “Projecting with MEMORY VIEWER input” (x page 185).
f When [AUTOPLAY] is set to [OFF] or [SCENARIO], [INTERVAL] cannot be set.
f Even if the setting for [INTERVAL] or [EFFECT] is changed while a still image or movie is being played back in the Memory Viewer, it is
not reected to the projected image being played back. Return to the Memory Viewer screen in the thumbnail view or list view and restart
playback.
f Even if [GUIDE] is set to [ON], the operation guide and the time bar will automatically erased approximately three seconds after playback is
started.
f Even if [GUIDE] is set to [OFF], the operation guide and the time bar is displayed during the fast-forward or rewind.
f Even if the operation guide is not displayed, operation of the Memory Viewer by asqw, the <ENTER> button, or the <AUTO SETUP/
CANCEL> button during the playback is enabled.
f The contents list that can be selected in [SCENARIO] of [AUTOPLAY] uses the “Delivering contents list” function of the “Multi Monitoring &
Control Software”.
f When [AUTOPLAY] is set to [SCENARIO], the playback order and the playback time follow the scenario le registered using the “Multi
Monitoring & Control Software”.
f When [AUTOPLAY] is set to [SCENARIO], the Light ID set with the “Multi Monitoring & Control Software” is transmitted.