Why are live and recorded images not displayed on my Panasonic WJ-ND400?
If live and recorded images are not displayed on your Panasonic DVR and you are logged in to a user's account with limited access privileges, log in to a user account as an administrator. Also, if you log in the network with domain authentication (Active Directory), ActiveX control cannot be installed sometimes, register trusted sites and add the security setting.
Why is the live image not displayed on my Panasonic DVR?
If the live image is not displayed on your Panasonic DVR, check the settings for [NW camera] and live video on the setup menu. Verify the IP address, subnet mask, and default gateway settings for both the recorder and the network camera. If the camera's compression format is set to M-JPEG and when saving from the recorder's setup menu or measuring from the program settings repeatedly, a few minutes of live image are not recorded and instead a black screen appears, wait about 10 minutes. If the camera image may not be displayed in MPEG-4 format images via the Internet, refer to your network administrator because it affects the router settings and other network devices.
Why is audio not recorded or played correctly on my Panasonic WJ-ND400?
If audio is not being recorded or played correctly on your Panasonic DVR, check if "Mic input" is selected for "Audio mode" and if "32 kbps" is selected for "Audio bit rate" on the setup menu of the network camera. If audio may not play when playing the most recent images while recording images or audio, stop and then start playing the images again.
How to fix buttons on browser window not displayed correctly Panasonic WJ-ND400?
If the buttons on the browser window of your Panasonic DVR are not displayed correctly, use the initial font settings. The browser's display may have troubles if you change the font settings from the initial settings.
What to do if SD memory data is not displayed on Panasonic WJ-ND400 DVR rec event list?
If the SD memory data is not displayed on the rec event list of your Panasonic DVR, filter the rec event list by using [SD memory] of the rec event search and then select rec event list to play images. Also, check the time set for the camera.
What to do if image is not being refreshed on Panasonic DVR?
If the image is not being refreshed on your Panasonic DVR, press [F5] on the keyboard to acquire the image again. This can happen due to congestion on the network.
How to fix cannot operate camera on Panasonic DVR?
If you cannot operate the camera with your Panasonic DVR, make sure that the number of the camera set in [NW camera] on the setup menu is correct. Also, ensure that the user name and password in [NW camera] on the setup menu have been input.
Why does my Panasonic DVR stop playback and restart after a short time?
If the Panasonic DVR stops playback and restarts after a short time, it is because time settings are changed through auto time adjustment. When the time in one record is not continuous, image playback may stop. In this case, playback will restart after a short time.
What to do if some information does not appear on Panasonic WJ-ND400 browser window?
If some information does not appear on the browser window of your Panasonic DVR, press [F5] on the keyboard to refresh the window.
Why cannot I close confirmation window on Panasonic WJ-ND400 DVR?
If you cannot close the confirmation window when the basic operation window opens on your Panasonic DVR, check the user name and password.
General| HDD size | 3.5 \ |
|---|---|
| HDD interface | Serial ATA |
| Number of HDDs supported | 54 |
| Compatible memory cards | SD |
| Ethernet LAN (RJ-45) ports | 1 |
| Supported network protocols | TCP/IP, UDP/IP, HTTP, FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, RTP |
| Power consumption (typical) | 170 W |
| Certification | UL, FCC, CE, C-UL, GOST, DOC |
| Operating temperature (T-T) | 5 - 45 °C |
| Operating relative humidity (H-H) | 5 - 90 % |
Weight and Dimensions| Weight | 13000 g |
|---|
To Next Page
