Need help?Do you have a question about the PAPILLON MULTICUTTER 33N and is the answer not in the manual?
Symbol indicating precaution, warning, or danger, requiring adherence to recommendations.
Indicates compliance with relevant safety standards.
Keep children, bystanders, and helpers 15 meters away from the brush cutter.
Warning that the exhaust and engine parts get hot during use.
Caution about flammable gasoline; avoid smoking or sparks near fuel.
Warning about thrown objects from cutting attachments; use blade guard.
Caution regarding risk of foot injury from cutting attachments.
Warning of danger from flying or thrown objects.
Instruction not to use serrated blades.
Requirement to wear head, hearing, and eye protection.
Recommendation to wear robust footwear.
Recommendation to wear protective gloves.
Read instructions, learn controls, and understand proper use and limitations of the appliance.
Inspect area, check blades, wear appropriate clothing, and ensure stable footing before use.
Operate in daylight, avoid wet grass, walk carefully, use caution on slopes, and avoid hazards.
Grip handles firmly, use idling position when suspending work.
Maintain engine speed as required for cutting, avoid unnecessary acceleration.
Turn off engine for grass obstructions, refueling, or checking the unit.
Stop engine immediately if blade hits stone; check and replace if damaged.
Turn off engine before responding to calls or moving to a new location.
Avoid touching spark plug or cord during operation to prevent electrical shock.
Do not touch hot engine parts like muffler during or after operation to avoid burns.
Turn off engine and position blade away from body when moving or storing.
Ensure cutting attachment has stopped rotating at idle before starting operation.
Keep fasteners tight, check grass catcher, replace worn parts for safe working condition.
Never store with fuel indoors where fumes can reach ignition sources; allow engine to cool.
Securely assemble the handle components onto the machine shaft.
Attach the safety guard using the provided hex key and wrench.
Assemble the cutting head, including releasing nuts and fitting the cutting head.
Follow safety instructions for filling the fuel tank with the correct gasoline-oil mix.
Ensure cutting head is assembled correctly and check for any faults or leaks before use.
Safely drain fuel by removing the tank cap and allowing fuel to run out.
Do not start until assembled; always check oil level before switching on the unit.
Verify device for leaks, defects, secure parts, and working safety devices before operation.
Follow steps for priming, switching on, choke adjustment, and pulling starter for engine ignition.
Operate the machine by engaging the throttle lever after pressing the lock-off lever.
Bump the nylon cutter to feed line before cutting operations.
Stop the machine using the engine switch or release throttle lever for cutting head stop.
Pull the safety belt pin to immediately release the brush cutter in case of problems.
Adjust throttle to ON position for restarting a hot machine.
Maintain 15m danger zone; wear PPE; do not start in tall grass; wait for cutter to stop.
Clean unit with cloth; avoid spraying with water to prevent engine damage.
Remove, clean, and gap the spark plug correctly for optimal engine performance.
Unclip cover, wash filter element in soap water, rinse, and dry naturally.
Clean unit thoroughly and store in a dry room after allowing the motor to cool down.
Check fuel level and reassemble blade/cutter if the engine does not run.
Address power loss by checking blade sharpness or consulting service center.
Ensure machines have adequate rest periods if the temperature becomes too high.
Provides information on the proper disposal of electrical and electronic equipment according to regulations.
Covers 24 months against manufacturing faults, excluding wear, improper maintenance, or misuse.
Explains the meaning of various safety symbols used in the manual.
Emphasizes reading instructions, proper use, and operator responsibility for safety.
Prepare the work area and wear appropriate clothing and PPE for safe operation.
Work in daylight, maintain balance, check machine operation, avoid foreign objects, and stop engine when unattended.
Ensure engine is off, blades stopped, and guards applied before transport.
Explains the meaning of NOTE, IMPORTANT, WARNING, and DANGER indicators.
Assemble the rod by inserting and tightening screws securely.
Connect the hedge trimmer by aligning pins and securing the knob.
Perform pre-work checks on screws, blades, guards, and handgrips.
Follow use directions, adjust tilt with motor off, and keep blades away from body parts.
Cut branches using upward curved movements for vertical trimming.
Use slow, curved movements with slight blade inclination for horizontal trimming.
Lubricate blades if they become excessively hot during operations.
Lubricate the gear guard every 20 hours using specified lithium-based grease.
Periodically check blades for damage; sharpen when performance decreases.
Secure machine in vehicle to prevent danger or tipping; mount bar cover.
Understand kickback causes and take precautions to prevent serious injury.
Assemble the pruner rod by inserting and securing the components.
Connect the pruner attachment to the rod by aligning pins and securing the knob.
Insert extension shaft between motor and attachment for higher access.
Perform pre-work checks on screws, bar, chain, handgrips, and oil delivery.
Check chain oil delivery and adjust flow rate if necessary.
Prune using specific techniques, avoid barking plants, and keep blades away from body parts.
Regularly check sprocket condition and replace if worn to ensure safety and efficiency.
Follow steps to sharpen chain edges correctly using appropriate files for safety.
Periodically turn and clean the bar, grease sprocket bearings, and remove burrs.
Lists required accessory codes for bar and chain to ensure compatibility and safety.
General| Brand | PAPILLON |
|---|---|
| Model | MULTICUTTER 33N |
| Category | Brush Cutter |
| Language | English |
To Next Page
