Parker V12 Series - Assembling Cylinder Barrel, Joint Shaft and Cover

Service/Spare Parts Manual
Series V12
MSG30-5506-M1/UK
5
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Assembling, shaft package
5
Parker Hannin
PumpandMotorDivision
Trollhättan,Sweden
ServiceManual
Series V12
HY30-5506-M1/UK
7.Pressdowntheshaftssealinthesealcar-
rierandassembletheretainingring.
8.Assemblethesealcarrierwithshaftseal
andtheretainingring.Makesureitisallthe
wayintothegroove.
Assembling, shaft package, cylinder barrel, joint shaft and cover
9.Assembletheguidepins.
10.Assembletheslidingplate.
11.Assemblethejointrollersonthejoint
shaft.Makesurethesteponthejointrollers
isttedinwards.
12.Assemblethedisplacementsettingscrew,
sealnutandtheO-ring.
5
Parker Hannin
PumpandMotorDivision
Trollhättan,Sweden
ServiceManual
Series V12
HY30-5506-M1/UK
7.Pressdowntheshaftssealinthesealcar-
rierandassembletheretainingring.
8.Assemblethesealcarrierwithshaftseal
andtheretainingring.Makesureitisallthe
wayintothegroove.
Assembling, shaft package, cylinder barrel, joint shaft and cover
9.Assembletheguidepins.
10.Assembletheslidingplate.
11.Assemblethejointrollersonthejoint
shaft.Makesurethesteponthejointrollers
isttedinwards.
12.Assemblethedisplacementsettingscrew,
sealnutandtheO-ring.
Assembling, shaft package, cylinder barrel, joint shaft and cover
7. Press down the shafts seal in the seal carrier and as-
semble the retaining ring.
.
8. Assemble the seal carrier with shaft seal and the re-
taining ring. Make sure it is all the way into the groove.
9. Assemble the guide pins. 10. Assemble the sliding plate.
5
Parker Hannin
PumpandMotorDivision
Trollhättan,Sweden
ServiceManual
Series V12
HY30-5506-M1/UK
7.Pressdowntheshaftssealinthesealcar-
rierandassembletheretainingring.
8.Assemblethesealcarrierwithshaftseal
andtheretainingring.Makesureitisallthe
wayintothegroove.
Assembling, shaft package, cylinder barrel, joint shaft and cover
9.Assembletheguidepins.
10.Assembletheslidingplate.
11.Assemblethejointrollersonthejoint
shaft.Makesurethesteponthejointrollers
isttedinwards.
12.Assemblethedisplacementsettingscrew,
sealnutandtheO-ring.
5
Parker Hannin
PumpandMotorDivision
Trollhättan,Sweden
ServiceManual
Series V12
HY30-5506-M1/UK
7.Pressdowntheshaftssealinthesealcar-
rierandassembletheretainingring.
8.Assemblethesealcarrierwithshaftseal
andtheretainingring.Makesureitisallthe
wayintothegroove.
Assembling, shaft package, cylinder barrel, joint shaft and cover
9.Assembletheguidepins.
10.Assembletheslidingplate.
11.Assemblethejointrollersonthejoint
shaft.Makesurethesteponthejointrollers
isttedinwards.
12.Assemblethedisplacementsettingscrew,
sealnutandtheO-ring.
11. Assemble the joint rollers on the joint shaft. Make
sure the step on the joint rollers is fitted inwards.
12. Assemble the displacement setting screw, seal nut
and the O-ring.
5
Parker Hannin
PumpandMotorDivision
Trollhättan,Sweden
ServiceManual
Series V12
HY30-5506-M1/UK
7.Pressdowntheshaftssealinthesealcar-
rierandassembletheretainingring.
8.Assemblethesealcarrierwithshaftseal
andtheretainingring.Makesureitisallthe
wayintothegroove.
Assembling, shaft package, cylinder barrel, joint shaft and cover
9.Assembletheguidepins.
10.Assembletheslidingplate.
11.Assemblethejointrollersonthejoint
shaft.Makesurethesteponthejointrollers
isttedinwards.
12.Assemblethedisplacementsettingscrew,
sealnutandtheO-ring.
5
Parker Hannin
PumpandMotorDivision
Trollhättan,Sweden
ServiceManual
Series V12
HY30-5506-M1/UK
7.Pressdowntheshaftssealinthesealcar-
rierandassembletheretainingring.
8.Assemblethesealcarrierwithshaftseal
andtheretainingring.Makesureitisallthe
wayintothegroove.
Assembling, shaft package, cylinder barrel, joint shaft and cover
9.Assembletheguidepins.
10.Assembletheslidingplate.
11.Assemblethejointrollersonthejoint
shaft.Makesurethesteponthejointrollers
isttedinwards.
12.Assemblethedisplacementsettingscrew,
sealnutandtheO-ring.