4
Quick Connect
Option
6" Lead
HALL EFFECT AND
REED SWITCH SPECIFICATIONS
Hall Effect and reed switches sense the position of the slide
housing by detecting the magnetic band on the cylinder piston.
Magnets are standard on all units. Switches are mounted on the
cylinder body and are easily positioned. Order switches sepa-
rately as well as the appropriate clamp shown in the table.
Hall Effect Switch Part No.
1
467150000 (PNP)
1467140000(NPN)
146715000C (NPN Quick Connect)
146714000C (NPN Quick Connect)
Reed Switch Part No.
1459030000- Standard
145903000C-Quick Connect
Model Clamp Part Number
04 L074730056
06 L074730075
08 L074730106
12 L074730150
PNP WIRING CONNECTION
Type: Solid State Type (PNP or NPN)
Switching Logic: Normally Open
Supply Voltage Range: 5 - 30VDC
Current Output Range: Up to100 mA at 5 VDC,
Up to 200 mA at 12 VDC and 24 VDC
Current Consumption: 7 mA at 5 VDC, 15 mA at 12 VDC,
and 30 mA at 24 VDC
Switching Response: 1000 Hz Maximum
Residual Voltage: 1.5V Maximum
Leakage Current: 10uA Maximum
Breakdown Voltage: 1.8kVACrms for 1 sec., lead to case
Min. Current for LED: 1mA
Operating Temperature: 14° to 140° F (-10° to 60° C)
Lead Wire Length: 39 inches (1meter)
SWITCH
LOAD
SWITCH
LOAD
BROWN**
(RED)
(WHITE)
BLACK**
BLUE**
(BLACK)
BROWN**
(RED)
BLACK**
(WHITE)
(BLACK)
+
_
+
_
DC 5 - 30V
DC 5 - 30V
Quick Connect
Option
1 Brown
3 Blue
4 Black
NPN WIRING CONNECTION
(RED)
SWITCH
_
+
LOAD
* When connecting Inductive
Load (relay, electromagnetic
valve etc.) it is recommended
to insert protection circuit.
Diode 100V 1A. (NPN
connection shown)
BROWN**
(BLACK)
(WHITE)
BLACK**
BLUE**
BLUE**
** Applies to Switches Manufactured
After 10/15/93.
Switching Logic: Normally Open
Voltage Rating: 85-125 VAC or 5-30 VDC*
Power Rating: 10 Watts AC or DC/Resistive Load
5 Watts AC or DC/Inductive Load
Switching
Current Range: 10-200 mA/Resistive Load
(PC, Sequencer)
10-100 mA/Inductive Load (Relay)
Switching Response: 300 Hz Maximum
Breakdown Voltage: 1.8kVACrms for 1 sec., lead to case
Min. Current for LED: 18mA
Operating Temperature: 14° to 140° F(-10° to 60° C)
Lead Wire Length: 39 inches (1 meter)
INTEGRAL CIRCUIT FOR
SWITCHING CONTACT PROTECTION
(Required for proper operation
24V DC)
Put Diode parallel to loads
following polarity as shown below.
(Recommended for longer
switch life 125V AC)
Put resistor and capacitor
parallel to loads.
DC 12V
D
CR
-
+
(WHITE)
BROWN**
(BLACK)
BLUE**
AC125V
R
C
=
=
-
+
(WHITE)
(BLACK)
BLUE**
BROWN**
CR
D: Diode: select a Diode with the breakdown
voltage and current rating according to the load.
CR: Relay coil (under 0.5W coil rating)
** Applies to Switches Manufactured
After 10/15/93.
CR: Relay coil (under 2W coil ratings)
R: Resistor under 1 K ohm
C: Capacitor 0.1 µF
4 Black
Not Used
1 Brown
Quick
Connect
Option
3 Blue
* Polarity is restricted for DC operation
(+) to BROWN (-) to BLUE
If these connections are reversed the contacts will close, but the LED will not light.
Prior to October, 1993:
(+) WHITE (-) BLACK
Additional information may be obtained from the Automation
Actuator Division in Wadsworth, Ohio or from your nearest
Parker Motion & Control Distributor.
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS
CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options
for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information
concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems,
the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all
performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by
Parker Hannifin Corporation and its subsidiaries at any time without notice.
WARNING
HALL EFFECT SPECIFICATIONS
REED SWITCH SPECIFICATIONS
1 BROWN
4 BLACK
3 BLUE
To Previous Page
Loading...
