To Next PageTo Next Page
Need help?Do you have a question about the Paso T3015DMA and is the answer not in the manual?
Overview of the Series DMS Integrated Amplifiers and their capabilities.
Details the features and intended uses of the amplifiers.
Lists detailed technical parameters, inputs, outputs, and power requirements.
Instructions for inspecting the unit upon receipt and handling transit damage.
Lists optional accessories such as rack mounting kits.
Crucial safety warnings and precautions for operating the amplifier.
Step-by-step guide for installing the amplifier into a standard equipment rack.
Details the function of each knob and switch on the amplifier's front panel.
Explains the various input/output terminals and their purposes on the rear panel.
Overview of the AMS Active Matrix Switching system setup.
Detailed explanation of how each switch in the AMS system functions.
Guides on configuring Input 1 for microphone connectivity.
Instructions for connecting microphones, including cable routing advice.
How to configure muting functions for priority during microphone use.
Specific wiring for desk base or gooseneck microphones with muting.
Detailed setup for muting priorities with microphone inputs.
Instructions for connecting a telephone system for paging.
How paging from the telephone system affects other inputs.
Guides on configuring Input 2 for microphone connectivity.
Muting configuration when using Input 2 as a microphone.
Explanation of the dual noiseless, fast-acting logic muting function.
Procedure for adjusting VOX sensitivity trimmers for optimal performance.
How to accomplish program muting by shorting MUTE and G terminals.
Diagram illustrating the timing of muting activation and restoration.
Chart detailing VOX and MUTE switch settings for priority.
Instructions for connecting high-level program sources like tuners or tape decks.
Details on the sensitivity attenuator and stereo summing for program inputs.
How the Program Input can be muted via VOX or direct muting.
Connecting balanced program sources like satellite receivers.
Guidance for connecting multiple amplifiers for networking.
Connecting general auxiliary sources like tuners or tape decks.
Connecting CD players or other high-level sources.
How Input 3 is muted by VOX or direct muting.
Connecting an external equalizer for frequency selective acoustic correction.
Instructions for bridging amplifiers to share inputs and controls.
Step-by-step guide for installing optional modules into the amplifier.
Diagram of module connector and how module muting works with VOX.
Wiring the remote volume control potentiometer for master volume adjustment.
Information on the 24V DC auxiliary power output for accessories.
Details on using the 1 Watt amplifier for Zone 1 and Music on Hold.
Explains MOH amplifier functions and common operational considerations.
Wiring diagrams for 600 Ohm and 8 Ohm MOH systems.
How to select the source and adjust the level for MOH output.
Instructions for connecting a message repeater through the telephone line.
Using the message repeater with the main output and muting music.
Guides on connecting speakers to the 8 Ohm outputs for Zone 1 and 2.
Details on operating Zone 1 and 2 and selecting their audio source.
Diagrams for series, parallel, and series-parallel speaker configurations.
Guidance on matching speaker load impedance for optimal power transfer.
Wiring diagram for 70 Volt constant voltage speaker distribution.
Advice for installation and using line attenuators for level control.
Explanation of the VOX relay for priority paging and its contacts.
Details on the 24V DC power supply for operating priority attenuators.
Using the PM03W module to equalize only the music program source.
Using the PM03W module with EQ Link to equalize all amplifier inputs.
Overview of system functions in a convenience store environment.
Diagram illustrating typical wiring for a C-store application.
Using the PM03W for independent music distribution in a separate zone.
Using PM03W with external tuner/CD player for music distribution.
Connecting PM03W to the amplifier's Mix Buss for a separate zone.
System functions for a restaurant with jukebox integration.
Diagram illustrating wiring for a restaurant jukebox application.
List of hardware components and transformers available for replacement.
List of electronic components for replacement, including resistors, capacitors, and semiconductors.
List of replacement controls and printed circuit boards.
Information on how to order replacement parts from the factory or distributors.
How to get help with installation, operation, or repair issues.
Details on in-warranty and out-of-warranty repair procedures and policies.
General
