To Next PageTo Next PageWhy does my PERFECTPASS StarGazer system accelerate past the set point?
If your PERFECTPASS system accelerates past the set point and is slow to return to the set speed, the engine throttle return spring may be weak. You can easily add a spring to resolve this issue.
What to do if my PERFECTPASS StarGazer Boating Equipment blown fuse?
A fuse typically blows when the red wire in the servo power cable is grounded or shorted. Check the wire for any breaks, pinches, or failures, especially near the gold resistor on the servo motor. Inspect the wire, and if needed, replace the fuse.
How to fix PERFECTPASS StarGazer Boating Equipment system surging in neutral?
If your PERFECTPASS system is surging in neutral, check the gap between the PerfectPass cable and the Morse control/Teleflex cable. Ensure there is no gap between them.
What to do if PERFECTPASS Boating Equipment is not controlling?
If the motor does not wind in or just vibrates, it's likely due to a bad electrical connection. Unplug both connectors at the servomotor and closely inspect the crimps and wiring.
Why is there no RPM tachometer reading on my PERFECTPASS StarGazer?
If the display tachometer reading is 00, ensure the RPM sensor is plugged into the correct port on the Master Module.
How to correct the time on the PERFECTPASS StarGazer Boating Equipment display?
To adjust the time on your PERFECTPASS, go to User Settings by pressing the Menu and UP Key together. Then, adjust the time for your specific area.
How to improve display readability on PERFECTPASS StarGazer Boating Equipment?
If the display is hard to read, adjust the contrast in the settings.
General| Brand | PERFECTPASS |
|---|---|
| Model | StarGazer |
| Category | Boating Equipment |
| Language | English |
Guides through the initial system setup procedure for boat and engine familiarization.
Explains the user interface, including screen activation, ON/OFF controls, and engaging the system.
Details the function of ON/Off, Menu, UP, and DOWN buttons for system navigation and control.
Overview of available slalom modes: CAL BASELINE, GPS Slalom, Practice, Classic, and Simple Slalom.
Explanation of the Crew Weight feature and how to use it for calibration accuracy.
Procedure for calibrating baseline RPM settings in a course using timing for accuracy.
Instructions for using GPS Slalom mode, including speed selection and skier size.
Guidance on using Practice Mode for training at in-between speeds and adjusting set speed.
Instructions for operating the PerfectPass system in Classic Mode, which is non-GPS enhanced.
Guide to using Simple Slalom mode, focusing on setting speed and using 'Pull Factor' adjustment.
Overview of Jump Mode, emphasizing the need for a proper course and integrated timing for accurate operation.
How RPM Adjust controls overall times by adding or reducing RPM for segment adjustments.
Displays mode name or skier's name; accessing Name List for jumper details and settings.
Explains how the speed readout functions as SETPOINT below 1500 RPM or when highlighted.
Displays timing information from the last pass, including segment errors and tolerance indicators.
Explains how Jump Letter combines weight, distance, and ability to determine throttle response.
Details S2% as a percentage of Jump Letter RPM applied to the 2nd segment for acceleration.
Allows fine adjustment of the 2nd segment only, affecting RPM for speed changes.
Procedure to enter new jumper details for automatic calculation of Jump Letter based on input.
Functionality of RTB mode where boat speed returns to baseline in the second segment.
Enables the boat to accelerate in the second segment, indicated by '(FAST)' on screen.
Step-by-step guide to setting RPM Baseline values for specific speeds for accurate timing.
Guidance for experienced drivers and skiers on optimal pull, Jump Letter selection, and throttle control.
Configuration options for Jump Mode, including crew weight, calibration, and throttle adjustments.
Table of typical Jump Settings (S2%, S2 RTB, CT) for various boat models and jumper types.
Instructions for using Trick Mode, controlled by GPS data for desired speed and go.
Setting the desired speed for boat engagement and control, adjustable on the fly.
Navigating to change modes or access KD settings for Trick Mode.
Guidance on smooth driving to the SETPOINT for seamless system takeover and safety tips.
Adjustable parameter controlling the 'firmness of the Pull' in Trick Mode, with a normal range of 14-28.
Operating RPM Mode, similar to Wakeboard/Trick, but controlling to an RPM SETPOINT.
Setting the desired RPM for system engagement and control.
Navigating to change modes or access settings within RPM Mode.
Instructions for towing skiers and engaging the system by reaching the RPM SETPOINT smoothly.
Speed-based mode using GPS Data, similar to TRICK mode for controlling desired speed.
Setting the desired speed for boat engagement and control, adjustable on the fly.
Displays Mode Name or Skier's Name pulled from the Name List.
Navigating to change modes or mode settings.
Guidance on smoothly driving to SETPOINT for seamless control and safety considerations.
Adjustable parameter for pull characteristic, with higher values meaning more aggressive response.
Instructions to locate and select 'Map Courses' from the event modes to begin mapping.
Procedure to enter coordinates for Course 1 by passing through entrance gates and pressing UP/DOWN keys.
Adjusting screen contrast using UP or DOWN keys for visibility in bright sun.
Setting the backlighting level of the display, with a range of 0-5.
Storing up to eight names and preferred speeds, accessible via NAME/MODE section.
Step-by-step guide to entering new names, modes, and speeds into the system.
Accessing software version, battery volts, system hours, and water temperature information.
Testing Rope Switch and Servo Motors for proper operation.
Switching display units and configuring engine setup, including RPM signal selection.
Displaying latitude, longitude, and GPS Clock status, with instructions to set the clock.
Detailed steps for mounting the servo motor and connecting the throttle cable linkage.
Importance of testing servo motor and cable for free movement and proper alignment.
Performing a quick linkage test to confirm smooth operation and identify any cable catching issues.
Mounting the Master Module under the dash and routing cables for system connection.
Installing the In Dash or External PerfectPass Display unit.
Connecting the power wire to a switched 12-volt source based on boat model.
Connecting the RPM sensor cable based on boat brand, model, and gauge system.
Verifying that the manual throttle operates normally after PerfectPass installation.
Guidelines for installing the GPS Receiver on the dash for optimal sky view.
Critical warning about connecting the GPS Receiver only to the designated 'GPS' port on the Master Module.
Troubleshooting steps for when the system is not controlling, focusing on servo motor and linkage.
Procedure to test the servo motor's 'auto tighten' function for proper operation.
Performing a linkage test to ensure smooth throttle cable movement and alignment.
Diagnosing and fixing neutral surge issues by checking the gap between PerfectPass and Morse control cables.
Addressing acceleration past set point, potentially due to weak engine return spring or cable issues.
Conducting an on-water test with engine cover open to diagnose speed control issues.
Troubleshooting the absence of RPM readings by checking sensor connections and module port.
Identifying common causes for blown fuses, such as grounded or shorted servo power cables.
Procedure to reset the entire system to factory specifications, including baseline RPM values.
Option to run in Wakeboard only mode or return to the full event menu.
Adjusting display contrast to improve readability, especially in bright sunlight.
Explanation of the All Buoy Timing Method (ABT) for determining boat speed and timing tolerances.
Information on the minimum magnet and Smart Timer requirements for running ABT.
Essential instructions for the purchaser to read, sign, and mail the agreement.
Details purchaser's assumption of risks and release of liability for the PerfectPass Speed Control device.
Guidance on how to obtain warranty service, whether factory installed, dealer installed, or company purchased.
Contact information and hours for PerfectPass Control Systems Inc. technical support and warranty claims.
