PFT G 5 SUPER - Page 39

PFT G 5 SUPER Operating Manual Issued 11.2008
Knauf PFT GmbH & Co.KG
39
Ltem. Qty. Part no. Description
1 1 00 00 82 23 Chassis G 5 cpl. RAL2004
2 1 00 07 27 90
Star wheel ring nut M 24 galv.
3 1 00 04 89 43 Star wheel G 5 pressed cpl. RAL 2004
4 1 00 04 64 73 Star wheel G 5 pressed RAL2004
5 1 20 10 18 10 Star wheel fixing disc galv.
6 1 20 20 78 19 Hex. screw M 8 x 16 with collar
7 1 00 00 73 61 Protection grill G 5 RAL9002
8 1 20 10 10 10 Splint D 4.5 with ring
9 1 00 04 56 47 Anti dust plate G 5 c RAL 9002
10 1 00 04 58 48 Material hopper G 5 pressed RAL9002
11 1 20 10 11 00 Gasket cleaning cover G 4 20 x 15 x 670
12 1 00 00 23 58 Seal disc cleaning cover D = 173 mm
13 1 00 00 82 35 Cleaning hole cover G 5 RAL9002
14 1 20 20 79 50 Ring nut M8 DIN 582 galv.
15 1 20 20 96 01 Hex. screw M 10 x 45 DIN 931 galv.
16 1 00 01 13 86
Locking lever for mixing tube G 4 with knob
17 1 00 01 04 62 Handle plastic 25 x 12 locking lever
18 1 00 00 25 84
Locking lever for mixing tube G 4 with one notch RAL2004
19 1 00 08 80 29 Eccentric bush MS for G 4 locking lever
20 1 20 20 72 10 Safety nut M 10 DIN 985 galv.
21 2 20 20 78 00 Hex. screw M 8 x 30 DIN 933 galv.
22 2 20 20 72 00 Safety nut M 8 DIN 985 galv.
23 2 20 56 66 15 Folding handle 250mm RAL2004
24 2 00 00 69 47 Wheel with hub D=500mm
25 2 00 00 82 65 Washer 10.5 x 30 x 4
26 2 20 20 72 10 Safety nut M10 DIN 985 galv.
27 4 00 00 85 85 Hex. screw M10 x 85 DIN 931 galv.
28 2 00 00 83 89 Holding plate for support G 5 RAL2004
29 2 00 00 83 91 Wheel bearing support G 5 RAL2004
30 4 20 20 72 10 Safety nut M 10 DIN 985 galv.
31 4 20 48 33 08 Grooved ball bearing 6005 2RS
32 2 00 00 86 37 Dummy cover GL 55 x 3-5
33 1 00 00 82 34 Chassis G 5 RAL2004
34 1 00 00 90 89
Double lockable castor 230 mm bearing ratio 300 kg
35 2 00 00 83 58 Cover cap (PVC) 60 x 35
36 1 00 00 90 88 Castor 230 mm collapse load 300 kg
37 1 00 03 73 54 Dust protection for star wheel motor G 5 c RAL 2004
38 1 00 01 99 64 Clamp stripe rubber guard G 5 RAL2004
39 1 00 03 91 79
Supplementary-equipment kit for scraper at star wheel G 5
40 2 20 20 62 00 Safety nut M 6 DIN 985 galv.
41 1 00 02 26 02 Scraper for star wheel G 5
42 2 00 02 26 01 Flat screw M6 x 20 DIN 603 galv.
43 1 00 02 26 04 Clamp plate for scraper rubber RAL 2004