PFT RITMO M - User Manual

Table of Contents
2016-02-17
Operating manual
Mixing pump RITMO L / RITMO M
Overview - Operation
RITMO L
RITMO M
Article number of the operating manual: 00 14 14 08
Article number of the parts list-machine RITMO L: 00 22 22 56 / 00 24 64 44 / 00 23 20 48
Article number of the parts list-machine RITMO M: 00 06 49 61 / 00 07 84 01
Read the operating manual prior to starting any work!

Summary

Examination

Examination by machine operator

Operator checks safety devices and machine condition before each shift.

Periodic inspection

Technical data

Electrical specifications RITMO L

Electrical specifications RITMO M

Power values RITMO L

Power values RITMO M

Connections RITMO L; RITMO M

Water and air connections

Operating modes

Selector switch pump motor

Selector switch water

Intended use air compressor

Intended purpose air compressor

Safety systems air compressor

Emphasizes the importance of functioning safety equipment for compressor operation.

Preparation booster pump (accessory)

Initial start-up, fill pump

Start-up booster pump

Operation

Personal protective equipment

Lists essential personal protective equipment (PPE) required for operation.

Preparing the machine

Connecting the power supply 230 V

Safe procedure for connecting the machine to a 230V power supply.

Connecting the water supply

Connection of water from water tank

Switching on RITMO L

Putting RITMO L into operation

Step-by-step guide to start up and operate the RITMO L.

Switching on RITMO M

Putting RITMO M into operation

Step-by-step guide to start up and operate the RITMO M.

Presetting the water flow rate

Feeding dry material to the machine

Monitoring the machine

Putting the machine into operation

Check consistency of mortar

Start RITMO L in “flying mode”

Procedure for starting the RITMO L in "flying mode" for operation.

Mortar hoses

Prepare mortar hoses

Connect mortar hose

Compressed air supply

Connect and fix the air

Connecting the spraying gun

Apply mortar

Open the air tap at the spraying gun

Procedure for opening the air tap to start mortar application.

Stopping in case of emergency RITMO L; RITMO M

Emergency-stop switch

Procedures for using emergency stop functions in critical situations.

Action in case of power cut

Main switch to position “0”

How to set the main switch to the '0' position during a power cut.

Relieve mortar pressure

Steps to safely relieve any remaining mortar pressure.

Switching on RITMO L again after power failure

Procedure to restart RITMO L after a power interruption.

Work on troubleshooting

Reaction in the event of faults

Immediate actions and procedures when faults occur.

Table of faults

A comprehensive table listing faults, causes, solutions, and responsible personnel.

Conveyor stands still; clogging

Removal of clogging in hoses; signs for clogging

Identifies signs of clogging and operator steps for removal.

Removal of clogging in hoses

Run the pump motor in the backward mode

Procedure to run the pump motor backward to clear blockages.

Blockage cannot be cleared

End of work; Cleaning

Switching off power supplies

Safely switching off all power supplies before cleaning.

Clean mortar hose

Cleaning the mixing tube

Changing the pump; cleaning the pump

Place the machine on the back side

Switching off RITMO L

Switching off RITMO M

Measures in case of risk of frost

Disconnect water supply

Steps to disconnect water supply to prevent frost damage.

Maintenance

Blow dry water fitting

Safety

Safety precautions for personnel performing maintenance.

Maintenance work

Strainer screen

Air compressor slider control; air filter cleaning

Actions after completed maintenance

Disassembly

Electrical system

Safety measures for handling electrical systems during disassembly.

Disposal

PFT RITMO M Specifications

General

Brand	PFT
Model	RITMO M
Category	Water Pump
Language	English